HFBR-5963AL Avago Technologies US Inc., HFBR-5963AL Datasheet
HFBR-5963AL
Specifications of HFBR-5963AL
Available stocks
Related parts for HFBR-5963AL
HFBR-5963AL Summary of contents
Page 1
... Full compliance with the optical performance re- quirements of the FDDI PMD standard • Full compliance with the optical performance re- quirements of 100Base-FX version of IEEE802.3u • +3.3 V TTL signal detect output • Temperature range: HFBR-5963L 0 °C to +70 °C HFBR-5963AL -40 °C to +85 °C ...
Page 2
... IC which converts differential PECL logic signals, ECL referenced (shifted +3.3 V supply, into an analog LED drive current. Receiver Section The receiver section of the HFBR-5963L utilizes an InGaAs PIN photodiode coupled to a custom silicon transimped- ance preamplifier IC packaged in the optical subas- sembly portion of the receiver. ...
Page 3
Pin Descriptions: Pin 1 Receiver Signal Ground Directly connect this pin to the receiver ground plane. Pin 2 Receiver Power Supply Vcc RX Provide +3 via the recommended receiver power supply filter circuit. Locate the ...
Page 4
... The HFBR-5963L series of transceivers meet MIL-STD- 883C Method 3015.4 Class 2 products. Care should be used to avoid shorting the receiver data or signal detect outputs directly to ground without proper current limiting impedance ...
Page 5
Board Layout - Hole Pattern The Avago Technologies transceiver complies with the circuit board “Common Transceiver Footprint” hole pat- tern defined in the original multisource announcement which defined the package style. This drawing is reproduced in Figure ...
Page 6
SEE DETAIL 1 9.80 (0.386) 2.92 (.115) 3.28 (.129) Tcase REFERENCE POINT DETAIL 1 SCALE 3 x ALL DIMENSIONS IN MILLIMETERS (INCHES) Figure 5. Package Outline Drawing MAX. 48.19 (1.897) 13.14 (.517) MAX. MIN. TYP. 0.46 10 ...
Page 7
... HFBR-5961L AND OTHER PIN SFF MODULES. 4. HOLES FOR MOUNTING STUDS MUST NOT BE TIED TO SIGNAL GROUND BUT MAY BE TIED TO CHASSIS GROUND. 5. HOLES FOR HOUSING LEADS OPTIONAL AND NOT REQUIRED FOR HFBR- 5984L. IF NEEDED IN FUTURE, THESE HOLES MUST BE TIED TO SIGNAL GROUND. 6. ALL DIMENSIONS ARE IN MILLIMETERS (INCHES). ...
Page 8
... C TIMES – ns HFBR-1L/AL TRANSMITTER TEST RESULTS OF λ , ∆λ AND t ARE CORRELATED AND COMPLY C r/f WITH THE ALLOWED SPECTRAL WIDTH AS A FUNCTION OF CENTER WAVELENGTH FOR VARIOUS RISE AND FALL TIMES. Figure 7. Transmitter Output Optical Spectral Width (FWHM) vs. Transmitter Output Optical Center Wavelength and Rise/Fall Times. Regulatory Compliance ...
Page 9
... Data Input Voltage - Low Data Input Voltage - High Data and Signal Detect Output Load Differential Input Voltage (p-p) Transmitter Electrical Characteristics HFBR-5963L ( ºC to +70 º HFBR-5963AL (T = -40 ºC to +85 º Parameter Supply Current Power Dissipation Data Input Current - Low Data Input Current - High ...
Page 10
... Data Output Fall Time Signal Detect Output Voltage - Low Signal Detect Output Voltage - High Power Supply Noise Rejection Transmitter Optical Characteristics HFBR-5963L ( ºC to +70 º HFBR-5963AL (T = -40 ºC to +85 º Parameter Output Optical Power BOL 62.5/125 µ 0.275 Fiber EOL Output Optical Power BOL 50/125 µ ...
Page 11
... Receiver Optical and Electrical Characteristics HFBR-5963L ( ºC to +70 º HFBR-5963AL (T = -40 ºC to +85 º Parameter Input Optical Power at minimum at Window Edge OC-3 FE Input Optical Power at Eye Center OC-3 FE Input Optical Power Maximum OC-3 FE Operating Wavelength Systematic Jitter Contributed by the Receiver OC-3 ...
Page 12
... Signal detect output shall be de-asserted within 100 µs after a step decrease in the Input Optical Power. At Signal Detect Deassert, the receiver outputs Data Out and Data Out Bar go to steady PECL levels High and Low respectively. . The HFBR-L transceiver complies with the requirements for the trade-offs between center wavelength, spectral width, and rise/fall times shown in Figure . This figure is derived from the FDDI PMD standard (ISO/IEC 1- : 10 and ANSI X.1 - 10) per the description in ANSI T1E1 ...
Page 13
... LED (Operating Case Temperature 0 to +70 °C) HFBR-5963L 1300 nm LED (Operating Case Temperature -40 to +85 °C) HFBR-5963AL For product information and a complete list of distributors, please go to our web site: Avago, Avago Technologies, and the A logo are trademarks of Avago Technologies, Limited in the United States and other countries. ...