HSDL-3005-028 Avago Technologies US Inc., HSDL-3005-028 Datasheet
HSDL-3005-028
Specifications of HSDL-3005-028
Related parts for HSDL-3005-028
HSDL-3005-028 Summary of contents
Page 1
... IrDA® Physical Layer Specifications version 1.4 Low Power from 9.6 kbit/s to 115.2 kbit/s (SIR) and it is IEC 825-Class 1 Eye Safe. The HSDL-3005 has very low idle current and can be shutdown completely to achieve very low power consumption. In the shutdown mode, the PIN ...
Page 2
... Order Information Part Number Packaging Type HSDL-3005-021 Tape and Reel HSDL-3005-028 Tape and Reel Marking Information The unit is marked with a number “3” and “YWWLL” on the shield for Front option. For Top option, the part is marked as “YWW.” ...
Page 3
... Watt for 3.0 < Vled < 3.6 V 6.8 5%, 0.25 Watt @ Vled = 3.6 V 10.0 5%, 0.25 Watt for 3.6 Vled 4.5 V [1] CX1 0.47 F 20%, X7R Ceramic [1] CX2 , CX3 6.8 F 20%, Tantalum Note: 1. CX1 and CX2 must be placed within 0 HSDL-3005 to obtain optimum noise immunity. 3 Notes ...
Page 4
... Different Remote Control Configuration for HSDL-3005 The HSDL-3005 can operate in the single-TxD programmable mode or the two-TxD direct transmission mode SHUTDOWN (ACTIVE HIGH) TxD_IrDA • • • (ACTIVE HIGH) SHUTDOWN DRIVE IrDA LED TxD_RC (GND) (B) Single-TxD Programmable Mode SD TXD_IrDA TXD_RC The shutdown condition will set the transceiver to the default mode (IrDA). ...
Page 5
Absolute Maximum Ratings at T For implementations where case to ambient thermal resistance is 50 C/W. Parameter Storage Temperature Operating Temperature LED Supply Voltage Supply Voltage Output Voltage: RxD LED Current Pulse Amplitude Recommended Operating Conditions Parameter Operating Temperature Supply ...
Page 6
Electrical and Optical Specifications Specifications (Min. & Max. values) hold over the recommended operating conditions unless otherwise noted. Unspecified test conditions may be anywhere in their operating range. All typical values (Typ.) are at 25ºC, V Parameter Symbol Receiver Viewing ...
Page 7
Electrical and Optical Specifications (Cont’d.) Parameter Symbol Transceiver Input Current High I H Low I L Supply Current Shutdown I CC1 Idle (Standby) I CC2 Active I CC3 Notes in-band optical signal is a pulse/sequence where the peak ...
Page 8
... HSDL-3005-021 (Front) Package Dimensions MOUNTING CENTER C L 2.05 RECEIVER 2.85 8.0 3.0 1.85 NOTES: 1. ALL DIMENSIONS IN MILLIMETERS (mm). 2. DIMENSION TOLERANCE IS 0.2 mm UNLESS OTHERWISE SPECIFIED. 3. COPLANAITY: 0.05 TO -0.150 mm. 8 4.0 1.025 EMITTER 2.5 1.175 2.55 0.80 4.0 2.9 SOLDERING PATTERN 1.35 MOUNTING ...
Page 9
... HSDL-3005-021(Front) Tape and Reel Dimensions 4.0 0.1 UNIT 0.1 1.5 0 POLARITY PIN 8: VLED 8.4 0.1 PIN 1: GND 3.4 0.1 0.4 0.05 2.8 0.1 EMPTY PARTS MOUNTED (40 mm MIN.) DETAIL A LABEL 9 1.75 0.1 1.5 0.1 7.5 0.1 16.0 0.2 8.0 0.1 PROGRESSIVE DIRECTION LEADER (400 mm MIN ...
Page 10
... HSDL-3005-028 (Top) Package Dimensions 2 2.8 3.35 2.35 0.7 0.1 DATECODE MARKING NOTES: 1. ALL DIMENSIONS IN MILLIMETERS (mm). 2. DIMENSION TOLERANCE IS 0.2 mm UNLESS OTHERWISE SPECIFIED. 10 +0.05 2.8 3.6 -0.2 +0.05 2 1.8 1.55 1.55 -0 XXX 5.1 0.05 (MAX.) 7.5 0.3 SOLDERING PATTERN C L 2.20 1.45 ...
Page 11
... HSDL-3005-028 (Top) Tape and Reel Dimensions 60 TYP. 264 (MAX.) 5 3.1 0.1 A-A SECTION UNIT: mm SYMBOL Ao Bo SPEC 3.65 0.10 7.90 0.10 SYMBOL E F SPEC 1.75 0.10 7.50 0.10 NOTES SPROKET HOLE PITCH CUMULATIVE TOLERANCE IS 0.2 mm. 2. CARRIER CAMBER SHALL NOT BE MORE THAN 1 mm PER 100 mm THROUGH A LENGTH OF 250 mm. ...
Page 12
... HSDL-3005 Moisture Proof Packaging All HSDL-3005 options are shipped in moisture proof package. Once opened, moisture absorption begins. This part is compliant to JEDEC Level 4. OPENED (UNSEALED) NO BAKING YES IS NECESSARY PERFORM RECOMMENDED BAKING CONDITIONS Figure 7. Baking conditions chart. 12 UNITS IN A SEALED MOISTURE-PROOF PACKAGE PACKAGE IS ...
Page 13
... The cool down rate, R5, from the liquidus point of the solder (77 F) should not exceed 6 C per second maximum. This limitation is necessary to allow the PC board and HSDL-3005 castellations to change dimensions evenly, putting minimal stresses on the HSDL- 3005 transceiver. ...
Page 14
Appendix A: SMT Assembly Application Note 1.0 Solder Pad, Mask and Metal Stencil STENCIL APERTURE SOLDER MASK Figure 8. Stencil and PCBA. 1.1 Recommended Land Pattern MOUNTING CENTER C L 0.10 1.75 0.60 0.475 Figure 9. Land pattern. 14 METAL ...
Page 15
Recommended Metal Solder Stencil Aperture It is recommended that only a 0.152 mm (0.006 inch 0.127 mm (0.005 inch) thick stencil be used for solder paste printing. This is to ensure adequate printed solder paste volume and ...
Page 16
Appendix B: PCB Layout Suggestion The following PCB layout guidelines should be followed to obtain a good PSRR and EM immunity resulting in good electrical performance. Things to note: 1. The ground plane should be continuous under the part, but ...
Page 17
... DE-MODULATOR USER INTERFACE Figure 12. IR layout in mobile phone platform. 17 from 9.6 kb/s to 115.2 kb/s, and supports most remote control codes. The design of the HSDL- 3005 also includes the following unique features: • Spectrally suited to universal remote control transmission function. • Low passive component count. • ...
Page 18
... PCMCIA CONTROLLER RS232C DRIVER PDA PLATFORM Figure 13. IR layout in PDA platform. The link distance testing was done using typical HSDL-3005 units with SMC’s FDC37C669 and FDC37N769 Super I/O controllers. An IrDA link distance was demonstrated. Remote Control Operation The HSDL-3005 is spectrally suited to universal remote control transmission function ...
Page 19
... the width of the window the height of the window, and Z is the distance from the HSDL- 3005 to the back of the window. The distance from the center of the LED lens to the center of the photodiode lens is 5.1 mm. The equations for the size of the window are as follows ...
Page 20
Window Material Almost any plastic material will work as a window material. Polycarbonate is recommended. The surface finish of the plastic should be smooth, without any texture filter dye may be used in the window to make it ...
Page 21
Shape of the Window From an optics standpoint, the window should be flat. This ensures that the window will not alter either the radiation pattern of the LED, or the receive pattern of the photodiode. If the window must be ...
Page 22
For product information and a complete list of distributors, please go to our website: Avago, Avago Technologies, and the A logo are trademarks of Avago Technologies Limited in the United States and other countries. Data subject to change. Copyright © ...