E3S-R1E4 Omron, E3S-R1E4 Datasheet

Page 1

... Flat object Cylindrical object PNP Sensing of Sensing of glass wafers plastic bottles and LCD glass and other circuit boards transparent bottles E3S-R32 Ideal Ideal E3S-R31 Ideal --- E3S-R82 Ideal Ideal E3S-R81 Ideal --- E3S-R37 Ideal Ideal E3S-R36 Ideal --- E3S-R87 Ideal Ideal E3S-R86 Ideal --- ...

Page 2

... E3S-RS30B42-30 Part number Length Straight Connector Right angle connector 2 m (6.56 ft) Y96E-43SD2 5 m (16.40 ft) Y96E-43SD5 10 m (32.8 ft) Y96E-43SD10 1 m (3.28 ft) Horizontal Vertical E3S-R1E4 E3S-R1E42 E3S-R1B4 E3S-R1B42 Y96E-43RD2 Y96E- -43RD5 Y96E-43RD10 Part number E39-L2 E39-L59 E39-L60 E39-L7 Part number E39-R1 E39-L69 E39-L70 ...

Page 3

... Note: 1. The above sensing distances are possible when the E39-R1 Reflector is used. The E39-R1 Reflector is provided with the E3S-R. 2. Even though the excess gain indicator of the E3S-R is dimly lit during sensitivity adjustment of the E3S-R, the E3S-R will pro- vide stable operation if the ambient temperature does not rise or fall by more than 5°C (91°F) while the E3S-R is operating. ...

Page 4

... The following are the permeation rates of a various transparent objects on condition that a permeation rate of 100 means that there is no object within the sensing distance of the E3S-R. The permeation rate of any type of object sensed by the E3S-R must be as low as pos- sible for the stable sensing of the object. Before using the E3S-R to sense objects, use samples of the objects to check if the E3S-R can sense the samples easily ...

Page 5

... J REFLECTOR OPERATION RANGE (TYPICAL) E3S-R11/-R61/-R16/-R66/-R31/-R81/-R36/-R86 Distance (cm) J EXCESS GAIN VS. SET DISTANCE (TYPICAL) E3S-R11/-R61/-R16/-R66/-R31/-R81/-R36/-R86 with E39-R1 Operating level Operating level distance (mm) 6 E3S-R12/-R62/-R17/-R67/-R32/-R82/-R37/-R87 ...

Page 6

... Blue + (See Note 1.) Note: 1. Reverse the polarity of the power supply to change the output mode. 2. The E3S-RS30j and E3S-RS30j42 do not have a stability indicator. 3. This load is needed when voltage output to connect a transistor circuit is required. E3S-R31/-R32/-R81/-R82/-R36/-R37/-R86/-R87 Brown ...

Page 7

... Blue 0 V (See Note.) Brown when light (See Note.) is not received. Blue + (See Note.) Note: Reverse the polarity of the power supply to change the output mode of the E3S-R. 8 Timing charts Light received Light not received ON Light indicator OFF (red) Output ON transistor ...

Page 8

... Emitter The mounting bracket can be attached to this side. 1.2 NPN output E3S-R11 Type yp PNP output E3S-R31 Size A 42.3 (1.67) B 15.2 (0.60) J E3S-R61/-R62/-R81/-R82 12.4 (0.49) 16.5 (0.65) Light indicator (red) Stability indicator Sensitivity adjustor (green) (white 1.2 10.7 (0.42) The mounting bracket can be attached to this side ...

Page 9

... Type yp NPN output E3S-R16 PNP output E3S-R36 Size A 42.3 (1.67) B 15.2 (0.60) J E3S-R66/-R67/-R86/-R87 14.9 (0.59) Light indicator (red) Stability indicator (green) Sensitivity adjustor (white The mounting bracket can be attached to this side. E39-L60 Close Mounting Plate (attachment) (Attach the mounting plate or the plug cannot be connected ...

Page 10

... The E3S-RS30j4 does not have a green stability indicator. Receiver Sensitivity adjustor 74.6 (2.94 dia. 4.2 2.1R 2.1R 4.2 5 25.4 6.5 1.9 39 (0.07) (1.54) Note: The E3S-RS30j42 does not have a green stability indicator. 11 ...

Page 11

... Align the sensitivity adjuster knob with the groove on the sensitivity adjuster. The arrow should point toward the sensing head as shown in the illustration. Press the knob in place impossible to remove the sensitivity adjuster knob from the E3S-R after it has been installed. 12 40.3 (1.59 ...

Page 12

... Two, M4 slotted hexagon head bolts 25.4 9 (1.00) E39-L70 Mounting Bracket for E3S-Rjj Vertical Type (Included) OMRON ON- -LINE Global -- http://www.omron.com USA -- http://www.omron.com/oei Canada -- http://www.omron.com/oci Specifications subject to change without notice. Mounting Holes Two, M4 25.4 (1 ...