DE2E3KH222MN3A Murata, DE2E3KH222MN3A Datasheet - Page 21

• Manufacturer Part Number: DE2E3KH222MN3A
• Manufacturer: Murata
• Type: Ceramic Discr

Specifications of DE2E3KH222MN3A

• Tolerance (+ Or -): 20%
• Voltage: 250VAC
• Temp Coeff (dielectric): E
• Operating Temp Range: -25C to 125C
• Mounting Style: Through Hole
• Construction: Radial
• Lead Spacing (nom): 7.5mm
• Product Length (mm): Not Requiredmm
• Product Depth (mm): 7mm
• Product Height (mm): Not Requiredmm
• Product Diameter (mm): 10mm
• Lead Diameter (nom): 0.6mm
• Seated Plane Height: 13mm
• Capacitance: 2200pF
• Package / Case: Not Required
• Lead Free Status / RoHS Status: Compliant

!Note
• This PDF catalog is downloaded from the website of Murata Manufacturing co., ltd. Therefore, it’s specifications are subject to change or our products in it may be discontinued without advance notice. Please check with our
• This PDF catalog has only typical specifications because there is no space for detailed specifications. Therefore, please approve our product specifications or transact the approval sheet for product specifications before ordering.
sales representatives or product engineers before ordering.
!Note
No.
16
17
18
19
20
*
1
"room condition" Temperature: 15 to 35°C, Relative humidity: 45 to 75%, Atmospheric pressure: 86 to 106kPa
Continued from the preceding page.
Humidity
Loading
Life
Flame Test
Robustness
of
Terminations
Temperature
and
Immersion
Cycle
• Please read rating and !CAUTION (for storage, operating, rating, soldering, mounting and handling) in this catalog to prevent smoking and/or burning, etc.
• This catalog has only typical specifications because there is no space for detailed specifications. Therefore, please approve our product specifications or transact the approval sheet for product specifications before ordering.
Item
Appearance
Capacitance
Change
D.F.
I.R.
Dielectric
Strength
Appearance
Capacitance
Change
I.R.
Dielectric
Strength
Tensile
Bending
Appearance
Capacitance
Change
D.F.
I.R.
Dielectric
Strength
No marked defect
1000MΩ min.
Per Item 6
No marked defect
1000MΩ min.
Per Item 6
The capacitor flame discontinued as follows.
Lead wire should not be cut off. Capacitor should
not be broken.
No marked defect
1000MΩ min.
Per Item 6
Cycle
Char.
Char.
Char.
1 to 2
Char.
Char.
E
E
E
E
E
F
F
F
3
F
F
Capacitance Change
Capacitance Change
Capacitance Change
Specifications
Specifications
Specifications
Within ±20%
Within ±30%
Within ±20%
Within ±30%
Within ±20%
Within ±30%
Time (sec.)
D.F.V5.0%
D.F.V7.5%
D.F.V5.0%
D.F.V7.5%
15 max.
60 max.
DEJ Series Specifications and Test Methods
Apply the rated voltage for 500±12 hrs. at 40±2˚C in 90 to 95%
relative humidity.
Pre-treatment:
Post-treatment:
Apply a voltage of Table 2 for 1500 hrs. at 85±2˚C, relative
humidity 50% max.
Pre-treatment:
Post-treatment:
The capacitor should be subjected
to applied flame for 15 sec. and then
removed for 15 sec. until 3 cycles
are completed.
As shown in figure at right, fix the body of
capacitor, apply a tensile weight gradually to
each lead wire in the radial direction of capacitor
up to 10N and keep it for 10±1 sec.
Each lead wire should be subjected to 5N weight and then a
90° bend, at the point of egress, in one direction, return to
original position, and then apply a 90° bend in the opposite
direction at the rate of one bend in 2 to 3 sec.
The capacitor should be subjected to 5 temperature cycles,
then consecutively to 2 immersion cycles.
Pre-treatment:
Post-treatment:
Capacitor should be stored at 85±2˚C for 1 hr., then placed at
room condition*
Capacitor should be stored for 1 to 2 hrs. at room condition*
Capacitor should be stored at 85±2˚C for 1 hr., then placed at
room condition*
Capacitor should be stored for 4 to 24 hrs. at room condition*
Capacitor should be stored at 85±2˚C for 1 hr., then placed at
room condition*
Capacitor should be stored for 4 to 24 hrs. at room condition*
AC500V(r.m.s.), except that once each hour the voltage
is increased to AC1000V(r.m.s.) for 0.1 sec.
Step
Step
1
2
1
2
3
4
Gas Burner: Inside Dia. 9.5
Temperature (ºC)
1
1
1
65+5/-0
for 24±2 hrs. before initial measurements.
for 24±2 hrs. before initial measurements.
for 24±2 hrs.
Temperature (ºC)
0±3
<Temperature Cycle>
<Immersion Cycle>
Room temp.
Room temp.
Applied Voltage
-25+0/-3
85+3/-0
Test Method
<Table 2>
Time
(min)
15
15
Cycle time: 5 cycle
Cycle time: 2 cycle
Immersion
Time (min)
Water
Clean
water
water
Salt
W
30
30
3
3
Capacitor
Flame
(in mm)
1
C85E.pdf
1
1
19
.
08.10.29
.
.
5