TZ03R200Y169B00 Murata, TZ03R200Y169B00 Datasheet - Page 38

• Manufacturer Part Number: TZ03R200Y169B00
• Manufacturer: Murata
• Type: Ceramicr

Specifications of TZ03R200Y169B00

• Capacitance Range (min/max) (pf): 4.2/20
• Tolerance (+ Or -): 0% to 50%
• Voltage: 100VDC
• Temp Coeff (dielectric): N750±300 ppm/°C
• Operating Temp Range: -25C to 85C
• Mounting Style: Through Hole
• Construction: Side Adj
• Q: 500
• Failure Rate: Not Required
• Product Length (mm): 7mm
• Product Depth (mm): 7.5mm
• Product Height (mm): 7.2mm
• Product Diameter (mm): Not Requiredmm
• Lead Free Status / RoHS Status: Compliant

!Note
• This PDF catalog is downloaded from the website of Murata Manufacturing co., ltd. Therefore, it’s specifications are subject to change or our products in it may be discontinued without advance notice. Please check with our
• This PDF catalog has only typical specifications because there is no space for detailed specifications. Therefore, please approve our product specifications or transact the approval sheet for product specifications before ordering.
sales representatives or product engineers before ordering.
!Note
1. Do not use the trimmer capacitor under atmosphere
2. Before using trimmer capacitor, please store under
3. Do not store in or near corrosive gasses.
4. Use within 6 months of delivery.
5. Open the package just before using.
6. Prior to storing previously opened packages, the
7. Do not store under direct sunlight.
1. Soldering
(1) TZ03 series can be soldered by flow soldering
(2) Soldering condition
(3) The dimension of mounting hole should be Murata's
(4) When using soldering iron, the string solder
(5) Our recommended chlorine content of string
(6) Do not use water-soluble flux (for water cleaning).
Notice (Storage and Operating Condition)
of RTV silicone rubber (Room Temperature
Vulcanizing Silicone Rubber) except Acetone
liberating silicone sealant.
the condition of -10 to +40 degree C and 30 to
85%RH.
packaging should be heat-sealed. Avoid using
rubber bands for repackaging.
Notice (Soldering and Mounting)
Refer to the temperature profile.
If the soldering conditions are not suitable, e.g.,
method and soldering iron. Do not use reflow
soldering method.
excessive time and/or excessive temperature,
the trimmer capacitor may deviate from the
specified characteristics.
standard mounting hole used at flow soldering.
The amount of solder is critical. Insufficient
amounts of solder can lead to insufficient
soldering strength on PCB. Excessive amounts of
solder may cause bridging between the terminals
or contact failure due to flux wicking up.
shall be applied to the lower part of the
terminal only. Do not apply flux except to the
terminals. Excessive amounts of solder and/or
applying solder to the upper part of the
terminal may cause fixed rotor or the contact
failure due to flux invasion into the movable
part and/or the contact point. The soldering
iron should not come in contact with the plastic
case of the trimmer capacitor. If such contact
does occur, the trimmer capacitor may be damaged.
solder is 0.5wt% max.
To prevent the deterioration of trimmer
capacitor characteristics, apply flux only to
terminals.
• Please read rating and !CAUTION (for storage, operating, rating, soldering, mounting and handling) in this catalog to prevent smoking and/or burning, etc.
• This catalog has only typical specifications because there is no space for detailed specifications. Therefore, please approve our product specifications or transact the approval sheet for product specifications before ordering.
8. Do not use the trimmer capacitor under the
2. Mounting
3. Cleaning
4. Other
(1) Corrosive gasses atmosphere
(2) In liquid (ex. water, oil, medical liquid,
(3) Dusty / dirty atmosphere
(4) Direct sunlight
(5) Static voltage nor electric/magnetic fields
(6) Direct sea breeze
(7) Other variations of the above
(1) Do not apply excessive force (preferably 5.0 N
(2) Use the suitable PCB holes which are the same
(3) Do not apply bending stress more than 10.0N
(4) Mount trimmer capacitor in contact with PCB.
(5) In case of bending the terminals, do not apply
conditions listed below.
Isopropyl-alcohol and Ethyl-alcohol are applicable
solvents for cleaning. If you use any other types of
solvents, please evaluate performance by your set.
Moreover, please confirm no damage for trimmer
capacitor after cleaning by your conditions.
Note the polarity of the trimmer capacitor to
minimize influence by stray capacitance.
(Refer to the dimensions concerning the polarity.)
(ex. Chlorine gas, Hydrogen sulfide gas,
Ammonia gas, Sulfuric acid gas, Nitric oxide gas,
etc.)
organic solvent, etc.)
[Ref: 500gf] max.), when the trimmer capacitor
is mounted on the PCB.
pitch as the terminal of the trimmer capacitor.
If it would not fit with the terminal, the
excessive stress would be applied to the
terminal and the trimmer capacitor may deviate
from the specified characteristics.
(Ref: 1kgf) after the trimmer capacitor has
been mounted on the PCB.
excessive force to the body of the product and
prevent the terminal fixing part from damaging.
37
T13E.pdf
07.3.1
8