TCET1201 Vishay, TCET1201 Datasheet - Page 7

• Manufacturer Part Number: TCET1201
• Description: Transistor Output Optocouplers Phototransistor Out Single CTR 40-80%
• Manufacturer: Vishay

Specifications of TCET1201

• Isolation Voltage: 5000 Vrms
• Maximum Input Diode Current: 60 mA
• Maximum Reverse Diode Voltage: 6 V
• Output Device: Phototransistor
• Output Type: DC
• Configuration: 1 Channel
• Input Type: DC
• Maximum Collector Emitter Voltage: 70 V
• Maximum Collector Emitter Saturation Voltage: 0.3 V
• Current Transfer Ratio: 80 %
• Maximum Forward Diode Voltage: 1.6 V
• Maximum Collector Current: 50 mA
• Maximum Power Dissipation: 250 mW
• Maximum Operating Temperature: + 100 C
• Minimum Operating Temperature: - 40 C
• Package / Case: PDIP-4
• No. Of Channels: 1
• Optocoupler Output Type: Phototransistor
• Input Current: 50mA
• Output Voltage: 70V
• Opto Case Style: DIP
• No. Of Pins: 4
• Mounting Type: Through Hole
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant

www.vishay.com
7
TC
Vishay Sprague
PERFORMANCE AND RELIABILITY
The capacitors are tested in accordance with MIL-PRF-
49137, with specific requirements as follows:
Temperature Stability: When tested per MIL-PRF-49137/6,
capacitance shall be within ±15 % at - 55 °C and 85 °C, and
± 10 % at 25 °C after exposure to temperature extremes. DF
shall be within 200 % of initial limit at - 55 °C, 150 % of initial
limit at 85°C, and meet the initial at 25 °C. DCL shall be within
10 x initial limit at 85 °C, and meet the initial limit at 25 °C.
Moisture Resistance: (per Method 106 of MIL-STD-202)
After 10 cycles of 24 hours at 25 °C to 65 °C and 80 - 98 %
RH; capacitance shall be within ± 15 % of initial value, DF
within 1.5 x initial limit and leakage within 3 x initial limit.
Life: (per Method 108 of MIL-STD-202) after 1000 hours at
85 °C and rated voltage; capacitance shall be within ± 10 %
of initial limit, DF within initial limits, and leakage within
200 % of initial limit.
Surge Voltage: (per MIL-PRF-49317) After 1000 cycles at
85 °C and 1.3 x WVDC; capacitance shall be within ± 10 %
of initial limit, DF and leakage within initial limits.
Resistance to Soldering Heat: (per Method 210 0f
MILSTD- 202, Condition B) After immersion in 260 °C molten
solder to within a 1/4” of the body of the unit, there shall be
no evidence of mechanical or electrical degradation.
Solderability: (per Method 208 of MIL-STD-202) After
dipping leads in 235 °C molten solder to within 0.125” of the
body of the unit, the solder shall cover 95 % of the lead
surface.
Terminal Strength: (per Method 211 of MIL-STD-202) After
the following test there shall be no loosening of the terminals
or permanent damage to the terminals. Test Condition A:
(Pull Test) 0.010
2 pounds and 0.007
(Bend Test) All leads shall withstand 3 - 90° bends with a
1/2 pound applied force.
CAPACITANCE VS. TEMPERATURE
+ 10
-10
+ 5
- 5
0
- 40
"
- 10
leads withstand 1 pound, 0.016
"
leads 1/2 pound. Test Condition C:
+ 25
(MFD-WVDC)
Subminiature, Leaded Solid Tantalum Capacitors
For technical questions, contact: [e-mail]
TEMPERATURE °C
+ 85
"
leads
+ 100
Polar or Non-polar
IMPEDANCE VS. FREQUENCY
LEAKAGE CURRENT - TEMPERATURE
1.0
0.1
0.01
10K
500
200
100
2K
1K
10
2.0
1.0
0.5
0.2
0.1
5K
50
20
5.0
100
- 40
Hz
500 1
- 10
KHz
2 5
0
1µF - 20 V
10 20 50 100
FREQUENCY
+ 20
(MFD-WVDC)
(MFD-WVDC)
Document Number: 43005
TEMPERATURE °C
Revision: 12-Sep-07
100 µF - 10 V
500 1 2 5 10
KHz
+ 85
MHz