IL4216-X006 Vishay, IL4216-X006 Datasheet

IL4216-X006

Manufacturer Part Number

IL4216-X006

Description

Triac & SCR Output Optocouplers Phototriac Output, Low Input Current

Manufacturer

Vishay

Datasheet

1.IL4218.pdf (6 pages)

Specifications of IL4216-X006

Configuration

Maximum Continuous Output Current

300 mA

Maximum Input Current

60 mA

Maximum Operating Temperature

+ 100 C

Maximum Power Dissipation

300 mW

Maximum Reverse Diode Voltage

6 V

Minimum Operating Temperature

- 55 C

Output Type

Package / Case

PDIP-6

Typical Input Voltage

1.3 V

Zero-crossing Circuit

Output Device

Triac

Isolation Voltage

5300 Vrms

Peak Output Voltage (vdrm)

650 V

Maximum Input Voltage

1.5 V

Maximum Output Voltage

420 VAC

Minimum Trigger Current

0.7 mA (Typ)

Lead Free Status / RoHS Status

Lead free / RoHS Compliant

Current page: 1 of 6
Download datasheet (120Kb)

DESCRIPTION

The IL4216, IL4217, IL4218 consists of an AlGaAs IRLED

optically coupled to a pair of photosensitive non-zero

crossing SCR chips and are connected inversely parallel to

form a TRIAC. These three semiconductors are assembled

in a six pin 0.3 inch dual in-line package.

High input sensitivity is achieved by using an emitter

follower phototransistor and a cascaded SCR predriver

resulting in an LED trigger current of less than 1.3 mA (DC).

The use of a proprietary dV/dt clamp results in a static dV/dt

of greater than 10 kV/μs. This clamp circuit has a MOSFET

that is enhanced when high dV/dt spikes occur between

MT1 and MT2 of the TRIAC. The FET clamps the base of the

phototransistor when conducting, disabling the internal

SCR predriver.

The blocking voltage of up to 800 V permits control of

off-line voltages up to 240 V

than two, and is sufficient for as much as 380 V

handling capability is up to 300 mA RMS, continuous at

25 °C.

The IL4216, IL4217, IL4218 isolates low-voltage logic from

120, 240, and 380 VAC lines to control resistive inductive, or

capacitive loads including motors solenoids, high current

thyristors or TRIAC and relays.

Note

(1)

Document Number: 83630

Rev. 1.6, 20-Oct-10

ORDERING INFORMATION

AGENCY CERTIFIED/PACKAGE

UL, cUL, BSI, FIMKO

DIP-6

DIP-6, 400 mil, option 6

SMD-6, option 7

SMD-6, option 9

VDE, UL, cUL, BSI, FIMKO

DIP-6

DIP-6, 400 mil, option 6

SMD-6, option 7

SMD-6, option 9

21842-1

Also available in tubes, do not put T on the end.

Optocoupler, Phototriac Output, High dV/dt, Low Input Current

PART NUMBER

i179041-3

, with a safety factor more

For technical questions, contact:

D E

MT2

MT1

IL4216-X009T

. Current

IL4216-X007T

IL4216-X006

IL4216-X001

IL4216-X016

IL4216

600

optocoupleranswers@vishay.com

(1)

PACKAGE OPTION

FEATURES

• High input sensitivity I

• 300 mA on-state current

• High static dV/dt 10000 V/μs, typical

• Very low leakage < 10 μA

• Isolation test voltage 5300 V

• Compliant to RoHS Directive 2002/95/EC and

APPLICATIONS

• Solid state relay

• Industrial controls

• Office equipment

• Consumer appliances

AGENCY APPROVALS

• UL1577, file no. E52744 system code J

• CSA 93751

• DIN EN 60747-5-5 (VDE 0884) available with option 1

• BSI IEC60950; IEC60065

• FIMKO

in accordance to WEEE 2002/96/EC

BLOCKING VOLTAGE V

IL4217-X007

IL4217-X009

IL4217

700

IL4216, IL4217, IL4218

TAPE AND

REEL

Vishay Semiconductors

DRM

= 1.3 mA

(V)

RMS

> 0.7 mm

7.62 mm

Option 7

DIP

IL4218-X017T

IL4218-X019T

IL4218-X006

IL4218-X001

IL4218-X016

IL4218

800

www.vishay.com

> 0.1 mm

10.16 mm

Option 6

Option 9

(1)

Related parts for IL4216-X006

IL4216-X006 Summary of contents

Page 1

... UL1577, file no. E52744 system code J • CSA 93751 • DIN EN 60747-5-5 (VDE 0884) available with option 1 • BSI IEC60950; IEC60065 . Current AC • FIMKO # - PACKAGE OPTION BLOCKING VOLTAGE V 600 IL4216 IL4216-X006 IL4216-X007T IL4217-X007 (1) IL4216-X009T IL4217-X009 600 IL4216-X001 IL4216-X016 - - optocoupleranswers@vishay.com IL4216, IL4217, IL4218 Vishay Semiconductors = 1 ...

Page 2

... IL4216, IL4217, IL4218 Vishay Semiconductors ABSOLUTE MAXIMUM RATINGS PARAMETER INPUT Reverse voltage Forward current Surge current Power dissipation Derate linearly from 25 °C Thermal resistance OUTPUT Peak off-state voltage RMS on-state current Single cycle surge Power dissipation Derate linearly from 25 °C Thermal resistance ...

Page 3

... Typical values are for information only and are not part of the testing requirements. POWER FACTOR CONSIDERATIONS A snubber is not needed to eliminate false operation of the TRIAC driver because of the IL4216, IL4217, IL4218 high static and commutating dV/dt with loads between 1 and 0.8 power factors. When inductive loads with power factors less than 0 ...

Page 4

... IL4216, IL4217, IL4218 Vishay Semiconductors TYPICAL CHARACTERISTICS ( 1.0 1.1 1 LED Forward Voltage (V) F iil4116_01 Fig LED Forward Current vs. Forward Voltage 1.4 1 ° °C 1.1 A 1.0 0 100 °C A 0.8 0.7 0 Forward Current (mA) F iil4116_02 Fig Forward Voltage vs. Forward Current 10 000 τ ...

Page 5

... Option 7 7.62 typ. 0.7 4.6 4.1 8 min. 8.4 min. 10.3 max. optocoupleranswers@vishay.com IL4216, IL4217, IL4218 Vishay Semiconductors ISO method A 7.62 typ. 18° 2.95 ± 0.5 0.25 typ. 7.62 to 8.81 Option 9 9.53 10.03 7.62 ref. ...

Page 6

... Vishay product could result in personal injury or death. Customers using or selling Vishay products not expressly indicated for use in such applications their own risk and agree to fully indemnify and hold Vishay and its distributors harmless from and against any and all claims, liabilities, expenses and damages arising or resulting in connection with such use or sale, including attorneys fees, even if such claim alleges that Vishay or its distributor was negligent regarding the design or manufacture of the part ...

Related keywords

IL4216-X006 datasheet
IL4216-X006 data sheet
IL4216-X006 pdf datasheet
IL4216-X006 component
IL4216-X006 part
IL4216-X006 distributor
IL4216-X006 RoHS
IL4216-X006 datasheet download