MSP430-H2618 Olimex Ltd., MSP430-H2618 Datasheet
MSP430-H2618
Specifications of MSP430-H2618
Related parts for MSP430-H2618
MSP430-H2618 Summary of contents
Page 1
... MSP430-H2618 development board Copyright(c) 2009, OLIMEX Ltd, All rights reserved All boards produced by Olimex are RoHS compliant Rev. Initial, April 2009 Page 1 Users Manual ...
Page 2
... PCB: FR-4, 1.5 mm (0.062''), green soldermask, silkscreen component print Dimensions 46.99 x 46.99 mm (1.850 x 1.850") ELECTROSTATIC WARNING: The MSP430-H2618 board is shipped in protective anti-static packaging. The board must not be subject to high electrostatic potentials. General practice for working with static sensitive devices should be applied when working with this board. ...
Page 3
... PROCESSOR FEATURES: MSP430-H2618 board uses MCU MSP430F2618 from Texas Instruments with these features: Low Supply Voltage Range Ultra-Low Power Consumption: - Wake-Up From Standby Mode in Less Than - 16-Bit RISC Architecture, 62.5-ns Instruction Cycle Time - Three-Channel Internal DMA - 12-Bit Analog-to-Digital (A/D) Converter With Internal Reference, ...
Page 4
BLOCK DIAGRAM: Page 4 ...
Page 5
MEMORY MAP: Page 5 ...
Page 6
... SCHEMATIC: P_IN P_OUT 10pF C5 10pF 32KHz CON1 CON2 MSP430-H2618 Rev. Initial COPYRIGHT(C) 2009 WWW.OLIMEX.COM/DEV JTAG 47K 10nF Q1 C2 100nF C1 + 10uF(NA MSP430F2618 C7 20pF Page 6 C4 100nF 16 15 CON4 CON3 455KHz-8MHz(NA) C8 20pF ...
Page 7
... GND at CON4 pin 14 or pin 15 (MSP430F2618.pin 62 or 63). The board power consumption is less than 10 mA. RESET CIRCUIT: MSP430-H2618 reset circuit is realized with a pull-up resistor R1 (47k) and capacitor C3(10n). You could also reset the MCU with an active low level at the JTAG pin CON4 pin 10 (MSP430F2618.pin 58). Page 7 ...
Page 8
... CLOCK CIRCUIT: Quartz crystal 32 768 Hz is connected to MSP430F2618 pin 8 (XIN) and pin 9 (XOUT/TCLK). There is an option for a high speed crystal oscillator to be connected to the MSP430F2618 pin 52 (XT2OUT) and pin 53 (XT2IN). JUMPER DESCRIPTION: P_IN P_OUT When this jumper is closed, the board is power supplied by the standard JTAG pin 2 ...
Page 9
EXTERNAL CONNECTORS DESCRIPTION: JTAG: Pin # 1 TDO 3 TDI 5 TMS 7 TCK 9 GND 11 RST 13 NC Input Test Data In. This is the serial data input for the shift register. TDI Output Test Data Out. This ...
Page 10
CON1: Pin # 1 (1) DV CC1 3 (3) P6.4/A4 5 (5) P6.6/A6/DAC0 7 (7) V REF+ 9 (9) XOUT 11 (11) V REF- 13 (13) P1.1/TA0 15 (15) P1.3/TA2 CON2: Pin # Signal Name 1 (17) P1.5/TA0 3 (19) ...
Page 11
A 15 (31) P3.3/UCB0CLK/UCA0STE I/O UCB0CLK input/output. I/O UCB0SOMI I/O UCB0SIMO I/O USCI B0 slave transmit enable. UCB0STE Output UCA0TXD USCIA transmit data output in UART mode. I/O UCB0SDA I/O SCL I USB0SCL CON3: Pin # 1 (33) P3.5/UCA0RXD 3 ...
Page 12
CON4: Pin # 1 (49) P5.5/SMCLK 3 (51) P5.7/TBOUTH/SVSOU T 5 (53) XT2IN 7 (55) TDI/TCLK 9 (57) TCK 11 (59) P6.0/A0 13 (61) P6.2/A2 15 (63) DV SS1 Signal Name Pin# 2 (50) 4 (52) 6 (54) 8 (56) ...
Page 13
MECHANICAL DIMENSIONS: - All measures are in inches. Page 13 ...
Page 14
... AVAILABLE DEMO SOFTWARE : – MSP430-H2618_Blinking_Led You could find MSP430-H2618 demo software at www.olimex.com/dev Page 14 . ...
Page 15
... ORDER CODE: MSP430-H2618 – assembled and tested (no kit, no soldering required). How to order? You can order to us directly or by any of our distributors. Check our web Revision history: REV. Initial www.olimex.com/dev for more info. - created April 2009 Page 15 ...
Page 16
... This document is intended only to assist the reader in the use of the product. OLIMEX Ltd. shall not be liable for any loss or damage arising from the use of any information in this document or any error or omission in such information or any incorrect use of the product ...