25LC128-E/ST Microchip Technology, 25LC128-E/ST Datasheet
25LC128-E/ST
Specifications of 25LC128-E/ST
Related parts for 25LC128-E/ST
25LC128-E/ST Summary of contents
Page 1
... SS SI Serial Data Input SCK Serial Clock Input HOLD Hold Input V Supply Voltage CC * 25XX128 is used in this document as a generic part number for the 25AA128, 25LC128 devices. © 2009 Microchip Technology Inc. 25AA128/25LC128 Page Size Temp. Ranges 64 Byte I,E 64 Byte I Description The Microchip Technology Inc. 25AA128/25LC128 ...
Page 2
... ELECTRICAL CHARACTERISTICS (†) Absolute Maximum Ratings V .............................................................................................................................................................................6.5V CC All inputs and outputs w.r.t. V ......................................................................................................... -0. Storage temperature .................................................................................................................................-65°C to 150°C Ambient temperature under bias ...............................................................................................................-40°C to 125°C ESD protection on all pins ..........................................................................................................................................4 kV † NOTICE: Stresses above those listed under “Absolute Maximum Ratings” may cause permanent damage to the device ...
Page 3
... This parameter is not tested but ensured by characterization. For endurance estimates in a specific application, please consult the Total Endurance™ Model which can be obtained from Microchip’s web site: www.microchip.com. © 2009 Microchip Technology Inc. 25AA128/25LC128 Industrial (I -40°C to +85°C A ...
Page 4
... TABLE 1-2: AC CHARACTERISTICS (CONTINUED) AC CHARACTERISTICS Param. Sym. Characteristic No HOLD Hold Time HOLD Low to Output HZ High HOLD High to Output HV Valid 20 T Internal Write Cycle Time WC 21 — Endurance Note 1: This parameter is periodically sampled and not 100% tested begins on the rising edge of CS after a valid write sequence and ends when the internal write cycle is WC complete ...
Page 5
... SI HOLD FIGURE 1-2: SERIAL INPUT TIMING CS 2 Mode 1,1 Mode 0,0 SCK MSB in SO FIGURE 1-3: SERIAL OUTPUT TIMING SCK 13 MSB out SO SI © 2009 Microchip Technology Inc. 25AA128/25LC128 High-Impedance n Don’t Care High-Impedance 14 Don’t Care LSB in 3 Mode 1,1 ...
Page 6
... FUNCTIONAL DESCRIPTION 2.1 Principles of Operation The 25XX128 is a 16,384 byte Serial EEPROM designed to interface directly with the Serial Peripheral Interface (SPI) port of many of today’s popular microcontroller families, including Microchip’s PIC microcontrollers. It may also interface with microcon- trollers that do not have a built-in SPI port by using dis- crete I/O lines programmed properly in firmware to match the SPI protocol ...
Page 7
... SI High-Impedance SO © 2009 Microchip Technology Inc. 25AA128/25LC128 HV Generator EEPROM Array Page Latches Y Decoder Sense Amp. R/W Control Read data from memory array beginning at selected address Write data to memory array beginning at selected address Reset the write enable latch (disable write operations) Set the write enable latch (enable write operations) ...
Page 8
... FIGURE 2-2: BYTE WRITE SEQUENCE SCK Instruction High-Impedance SO FIGURE 2-3: PAGE WRITE SEQUENCE SCK Instruction SCK Data Byte DS21831D-page 16-bit Address 16-bit Address Data Byte Twc Data Byte Data Byte Data Byte n (64 max © 2009 Microchip Technology Inc. ...
Page 9
... FIGURE 2-5: WRITE DISABLE SEQUENCE (WRDI) CS SCK SI SO © 2009 Microchip Technology Inc. 25AA128/25LC128 The following is a list of conditions under which the write enable latch will be reset: • Power-up See • WRDI instruction successfully executed • WRSR instruction successfully executed • WRITE instruction successfully executed ...
Page 10
... Read Status Register Instruction (RDSR) The Read Status Register instruction (RDSR) provides access to the STATUS register. The STATUS register may be read at any time, even during a write cycle. The STATUS register is formatted as follows: TABLE 2-2: STATUS REGISTER W/R – – ...
Page 11
... SI SO Note: An internal write cycle (T WC © 2009 Microchip Technology Inc. 25AA128/25LC128 only writes to nonvolatile bits in the STATUS register are disabled. See Table 2-4 for a matrix of functionality on the WPEN bit. See Figure 2-7 for the WRSR timing sequence. TABLE 2-3: BP1 ...
Page 12
... Data Protection The following protection has been implemented to prevent inadvertent writes to the array: • The write enable latch is reset on power-up • A write enable instruction must be issued to set the write enable latch • After a byte write, page write or STATUS register write, the write enable latch is reset • ...
Page 13
... WP going low will have no effect on the write. © 2009 Microchip Technology Inc. 25AA128/25LC128 The WP pin function is blocked when the WPEN bit in the STATUS register is low. This allows the user to install the 25XX128 in a system with WP pin grounded and still be able to write to the STATUS register ...
Page 14
... DS21831D-page 14 : Example 25LC128 I/MF 0328 1L7 Example: 25AA128 I/P 1L7 0328 Example: 25LC128 I/SN 0328 1L7 Example: TSSOP 1st Line Marking 5LD Device I328 1L7 25AA128 25AA128X 25LC128 25LC128X © 2009 Microchip Technology Inc. std mark 5AD 5ADX 5LD 5LDX ...
Page 15
... Pin 1 visual index feature may vary, but must be located within the hatched area. 2. Package may have one or more exposed tie bars at ends. 3. Dimensioning and tolerancing per ASME Y14.5M. BSC: Basic Dimension. Theoretically exact value shown without tolerances. REF: Reference Dimension, usually without tolerance, for information purposes only. © 2009 Microchip Technology Inc. 25AA128/25LC128 ...
Page 16
... Plastic Dual In-Line (P) – 300 mil Body [PDIP] Note: For the most current package drawings, please see the Microchip Packaging Specification located at http://www.microchip.com/packaging N NOTE Number of Pins Pitch Top to Seating Plane Molded Package Thickness Base to Seating Plane Shoulder to Shoulder Width ...
Page 17
... Dimensions D and E1 do not include mold flash or protrusions. Mold flash or protrusions shall not exceed 0.15 mm per side. 4. Dimensioning and tolerancing per ASME Y14.5M. BSC: Basic Dimension. Theoretically exact value shown without tolerances. REF: Reference Dimension, usually without tolerance, for information purposes only. © 2009 Microchip Technology Inc. 25AA128/25LC128 ...
Page 18
... WKH PRVW FXUUHQW SDFNDJH GUDZLQJV SOHDVH VHH WKH 0LFURFKLS 3DFNDJLQJ 6SHFLILFDWLRQ ORFDWHG DW KWWS ZZZ PLFURFKLS FRP SDFNDJLQJ DS21831D-page 18 PP %RG\ >62,&@ © 2009 Microchip Technology Inc. ...
Page 19
... Dimensions D and E1 do not include mold flash or protrusions. Mold flash or protrusions shall not exceed 0.15 mm per side. 3. Dimensioning and tolerancing per ASME Y14.5M. BSC: Basic Dimension. Theoretically exact value shown without tolerances. REF: Reference Dimension, usually without tolerance, for information purposes only. © 2009 Microchip Technology Inc. 25AA128/25LC128 ...
Page 20
... APPENDIX A: REVISION HISTORY Revision B Corrections to Section 1.0, Electrical Characteristics. Revision C (5/07) Removed Preliminary status; Revised Table 1-2, Para. 7 and 8; Revised Table 1-3, CL; Revised trademarks; Replaced Package drawings (Rev. AP); Replaced On- Line Support; Revised Product ID section. Revision D (06/09) Added X-Rotated TSSOP to package types; Revised Table 1-2, Param. 21 ...
Page 21
... To register, access the Microchip web site at www.microchip.com, click on Customer Change Notification and follow the registration instructions. © 2009 Microchip Technology Inc. 25AA128/25LC128 CUSTOMER SUPPORT Users of Microchip products can receive assistance through several channels: • Distributor or Representative • ...
Page 22
... Telephone: (_______) _________ - _________ Application (optional): Would you like a reply? Y Device: 25AA128/25LC128 Questions: 1. What are the best features of this document? 2. How does this document meet your hardware and software development needs you find the organization of this document easy to follow? If not, why? 4 ...
Page 23
... Serial EEPROM, Industrial temp., Tape & Reel, SOIC package 25AA128T-I/ST = 128k-bit, 1.8V Serial EEPROM, Industrial temp., Tape & Reel, TSSOP package 25LC128-I/P = 128k-bit, 2.5V Serial EEPROM, Industrial temp., P-DIP package 25LC128T-E/MF = 128k-bit, 2.5V Serial EEPROM, Extended temp., Tape & Reel, DFN package 25LC128XT-I/ST = 128k-bit, 2 ...
Page 24
... NOTES: DS21831D-page 24 © 2009 Microchip Technology Inc. ...
Page 25
... PICDEM, PICDEM.net, PICtail, PIC Select Mode, Total Endurance, TSHARC, WiperLock and ZENA are trademarks of Microchip Technology Incorporated in the U.S.A. and other countries. SQTP is a service mark of Microchip Technology Incorporated in the U.S.A. All other trademarks mentioned herein are property of their respective companies. ...
Page 26
... Fax: 886-3-6578-370 Taiwan - Kaohsiung Tel: 886-7-536-4818 Fax: 886-7-536-4803 Taiwan - Taipei Tel: 886-2-2500-6610 Fax: 886-2-2508-0102 Thailand - Bangkok Tel: 66-2-694-1351 Fax: 66-2-694-1350 © 2009 Microchip Technology Inc. EUROPE Austria - Wels Tel: 43-7242-2244-39 Fax: 43-7242-2244-393 Denmark - Copenhagen Tel: 45-4450-2828 Fax: 45-4485-2829 France - Paris Tel: 33-1-69-53-63-20 ...