AD5640CRM-2 Analog Devices Inc, AD5640CRM-2 Datasheet - Page 21

• Manufacturer Part Number: AD5640CRM-2
• Description: IC,D/A CONVERTER,SINGLE,14-BIT,CMOS,TSSOP,8PIN
• Manufacturer: Analog Devices Inc
• Series: nanoDAC™r

Specifications of AD5640CRM-2

• Settling Time: 8µs
• Number Of Bits: 14
• Data Interface: DSP, MICROWIRE™, QSPI™, Serial, SPI™
• Number Of Converters: 1
• Voltage Supply Source: Single Supply
• Power Dissipation (max): 5mW
• Operating Temperature: -40°C ~ 105°C
• Mounting Type: Surface Mount
• Package / Case: 8-MSOP, Micro8™, 8-uMAX, 8-uSOP,
• Lead Free Status / RoHS Status: Contains lead / RoHS non-compliant

APPLICATIONS INFORMATION
USING A REF19x AS A POWER SUPPLY FOR THE
AD5620/AD5640/AD5660
Because the supply current required by the AD5620/AD5640/
AD5660 is extremely low, an alternative option is to use a REF19x
voltage reference (REF195 for 5 V or REF193 for 3 V) to supply
the required voltage to the part (see Figure 49). This is especially
useful if the power supply is quite noisy or if the system supply
voltages are at some value other than 5 V or 3 V, for example, 15 V.
The REF19x outputs a steady supply voltage for the AD5620/
AD5640/AD5660. If the low dropout REF195 is used, the current
it needs to supply to the AD5660 is 500 μA. This is with no load
on the output of the DAC. When the DAC output is loaded, the
REF195 also must supply the current to the load. The total current
required (with a 5 kΩ load on the DAC output) is
The load regulation of the REF195 is typically 2 ppm/mA,
which results in an error of 3 ppm (15 μV) for the 1.5 mA
current drawn from it. This corresponds to a 0.197 LSB error
for the AD5660.
INTERFACE
500 μA + (5 V/5 kΩ) = 1.5 mA
SERIAL
3-WIRE
Figure 49. REF195 as the Power Supply to the AD5660
15V
SYNC
SCLK
DIN
REF195
5V
AD5660
V
OUT
= 0V TO 5V
Rev. F | Page 21 of 28
BIPOLAR OPERATION USING THE AD5660
The AD5660 is designed for single-supply operation, but a
bipolar output range is also possible using the circuit in
Figure 50. Figure 50 gives an output voltage range of ±5 V.
Rail-to-rail operation at the amplifier output is achievable
using an AD820 or an OP295 as the output amplifier.
The output voltage for any input code can be calculated as
where D represents the input code in decimal (0 to 65535).
When V
This results in an output voltage range of ±5 V, with 0x0000
corresponding to a −5 V output and 0xFFFF corresponding to a
+5 V output.
+5V
V
V
O
O
DD


10F






= 5 V, R1 = R2 = 10 kΩ,
V
10
65536
DD
Figure 50. Bipolar Operation with the AD5660

 
D
0.1F





65536

D
5
V
V
DD
AD5620/AD5640/AD5660

 

INTERFACE
AD5660
3-WIRE
SERIAL
10k



R1
R1
R1

V
V
OUT
R2
FB




V
DD
 
AD820/
OP295


+5V
10k
–5V
R2
R2
R1






±5V