ADSP-21262SBBCZ150 Analog Devices Inc, ADSP-21262SBBCZ150 Datasheet - Page 18

• Manufacturer Part Number: ADSP-21262SBBCZ150
• Description: IC,DSP,32-BIT,CMOS,BGA,136PIN,PLASTIC
• Manufacturer: Analog Devices Inc
• Series: SHARC®r
• Type: Fixed/Floating Pointr

Specifications of ADSP-21262SBBCZ150

• Interface: DAI, SPI
• Clock Rate: 150MHz
• Non-volatile Memory: ROM (512 kB)
• On-chip Ram: 256kB
• Voltage - I/o: 3.30V
• Voltage - Core: 1.20V
• Operating Temperature: -40°C ~ 85°C
• Mounting Type: Surface Mount
• Package / Case: 136-CSPBGA
• Device Core Size: 32/40Bit
• Architecture: Super Harvard
• Format: Floating Point
• Clock Freq (max): 150MHz
• Mips: 150
• Device Input Clock Speed: 150MHz
• Ram Size: 256KB
• Program Memory Size: 512KB
• Operating Supply Voltage (typ): 1.2/3.3V
• Operating Supply Voltage (min): 1.14/3.13V
• Operating Supply Voltage (max): 1.26/3.47V
• Operating Temp Range: 0C to 70C
• Operating Temperature Classification: Commercial
• Mounting: Surface Mount
• Pin Count: 136
• Package Type: CSPBGA
• Package: 136CSP-BGA
• Numeric And Arithmetic Format: Floating-Point
• Maximum Speed: 150 MHz
• Device Million Instructions Per Second: 150 MIPS
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant

ADSP-21262
Power-Up Sequencing
The timing requirements for DSP startup are given in
and
Table 9. Power-Up Sequencing (DSP Startup)
1
2
3
4
5
Parameter
Timing Requirements
t
t
t
t
t
Switching Characteristic
t
Valid V
Assumes a stable CLKIN signal, after meeting worst-case startup timing of crystal oscillators. Refer to the crystal oscillator manufacturer’s data sheet for startup time.
Based on CLKIN cycles.
Applies after the power-up sequence is complete. Subsequent resets require a minimum of four CLKIN cycles for RESET to be held low in order to properly initialize and
The 4096 cycle count depends on t
RSTVDD
IVDDEVDD
CLKVDD
CLKRST
PLLRST
CORERST
depending on the design of the power supply subsystem.
Assume a 25 ms maximum oscillator startup time if using the XTAL pin and internal oscillator circuit in conjunction with an external crystal.
propagate default states at all I/O pins.
4097 cycles maximum.
Figure
DDINT
/V
6.
DDEXT
assumes that the supplies are fully ramped to their 1.2 and 3.3 volt rails. Voltage ramp rates can vary from microseconds to hundreds of milliseconds
CLKCFG1–0
RSTOUT
V DDEXT
RESET Low Before V
V
CLKIN Valid After V
CLKIN Valid Before RESET Deasserted
PLL Control Setup Before RESET Deasserted
DSP Core Reset Deasserted After RESET Deasserted
V DDINT
RESET
DDINT
CLKIN
SRST
On Before V
*
*
MULTIPLEXED WITH CLKOUT
specification in
t
RSTVDD
DDEXT
DDINT
DDINT
Table
/V
/V
DDEXT
DDEXT
11. If setup time is not met, one additional CLKIN cycle may be added to the core reset time, resulting in
Rev. B | Page 18 of 48 | August 2005
Valid
Figure 6. Power-Up Sequencing
On
Table 9
1
t
IVDDEVDD
t
PLLRST
t
t
CLKVDD
CLKRST
Min
0
–50
0
10
20
4096t
t
CORERST
2
3
CK
4, 5
Max
200
200
Unit
ns
ms
ms
µs
µs