ATS616LSGTN-T Allegro Microsystems Inc, ATS616LSGTN-T Datasheet - Page 9

• Manufacturer Part Number: ATS616LSGTN-T
• Description: IC,HALL-EFFECT SWITCH,DIFFERENTIAL,BIPOLAR,SIP,4PIN,PLASTIC
• Manufacturer: Allegro Microsystems Inc
• Type: Special Purposer

Specifications of ATS616LSGTN-T

• Rohs Compliant: YES
• Sensing Range: 60G
• Voltage - Supply: 3.5 V ~ 24 V
• Current - Supply: 12mA
• Current - Output (max): 55mA
• Output Type: Digital, Open Collector
• Features: Gear Tooth Type
• Operating Temperature: -40°C ~ 150°C
• Package / Case: 4-SIP
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• Other names: 620-1116-2

ATS616LSG
Assembly Description.
pellet configuration that is fully optimized to provide digi-
tal response to gear tooth edges. This device is packaged in a
molded miniature plastic body that has been optimized for size,
ease of assembly, and manufacturability. High operating tem-
perature materials are used in all aspects of construction.
After proper power is applied to the component, the IC is
capable of instantly providing digital information that is repre-
sentative of the profile of a rotating gear. No additional optimi-
zation or processing circuitry is required. This ease of use should
reduce design time and incremental assembly costs for most
applications.
Hall Technology.
Hall effect sensor IC, a samarium cobalt pellet, and a flat ferrous
pole piece (figure 2). The Hall IC consists of 2 Hall elements
(spaced 2.2 mm apart) located so as to measure the magnetic
gradient created by the passing of a ferromagnetic object. The
two elements measure the magnetic gradient and convert it to an
analog voltage that is then processed in order to provide a digital
output signal.
The Hall IC is self-calibrating and also possesses a tempera-
ture compensated amplifier and offset cancellation circuitry. Its
voltage regulator provides supply noise rejection throughout the
operating voltage range. Changes in temperature do not greatly
affect this device due to the stable amplifier design and the offset
Figure 2. Relative motion of the target is detected by the dual Hall ele-
ments mounted on the Hall IC.
Hall Effect Device
Hall Element 2
Dual-Element
Target (Gear)
(Pin n >1 Side)
The package contains a single-chip differential
The ATS616 is a Hall IC/rare earth
South Pole
North Pole
Dynamic Self-Calibrating Peak-Detecting Differential
(Pin 1 Side)
(Concentrator)
Element Pitch
Hall Element 1
Hall IC
Pole Piece
Back-biasing
rare-earth pellet
Case
Functional Description
rejection circuitry. The Hall transducers and signal processing
electronics are integrated on the same silicon substrate, using a
proprietary BiCMOS process.
Internal Electronics.
peak detection scheme to eliminate magnet and system offsets.
This technique allows dynamic coupling and filtering of offsets
without the power-up and settling time disadvantages of classical
high-pass filtering schemes. The peak signal of every tooth and
valley is detected by the filter and is used to provide an instant
reference for the operate and release point comparator. In this
manner, the thresholds are adapted and referenced to individual
signal peaks and valleys, providing immunity to zero line varia-
tion from installation inaccuracies (tilt, rotation, and off-center
placement), as well as for variations caused by target and shaft
eccentricities. The peak detection concept also allows extremely
low speed operation for small value filter capacitors.
The ATS616 also includes self-calibration circuitry that is
engaged at power on. The signal amplitude is measured, and
then the device gain is normalized. In this manner switchpoint
drift versus air gap is minimized, and excellent timing accuracy
can be achieved.
The AGC (Automatic Gain Control) circuitry, in conjunction
with a unique hysteresis circuit, also eliminates the effect of
gear edge overshoot as well as increases the immunity to false
switching caused by gear tooth anomalies at close air gaps. The
Figure 3. The peaks in the resulting differential signal are used to set the
operate, B
Differential
Magnetic Flux
Device Output
V
OUT
V
Hall Effect Gear Tooth Sensor IC
OUT(sat)
OP
V
B+
0
B–
CC
, and release, B
The processing circuit uses a patented
RP
115 Northeast Cutoff
1.508.853.5000; www.allegromicro.com
Allegro MicroSystems, Inc.
Worcester, Massachusetts 01615-0036 U.S.A.
, switchpoints.
B
OP
B
RP
B
OP
B
RP
9