CY7C63613C-SXC Cypress Semiconductor Corp, CY7C63613C-SXC Datasheet - Page 13

• Manufacturer Part Number: CY7C63613C-SXC
• Description: IC,MICROCONTROLLER,8-BIT,SOP,24PIN,PLASTIC
• Manufacturer: Cypress Semiconductor Corp
• Series: M8™r

Specifications of CY7C63613C-SXC

• Applications: USB Microcontroller
• Core Processor: M8B
• Program Memory Type: OTP (8 kB)
• Controller Series: CY7C636xx
• Ram Size: 256 x 8
• Interface: PS2, USB
• Number Of I /o: 16
• Voltage - Supply: 4 V ~ 5.5 V
• Operating Temperature: 0°C ~ 70°C
• Mounting Type: Surface Mount
• Package / Case: 24-SOIC (7.5mm Width)
• Processor Series: CY7C63xx
• Core: M8B
• Data Bus Width: 8 bit
• Program Memory Size: 8 KB
• Data Ram Size: 256 B
• Interface Type: PS2, USB
• Maximum Clock Frequency: 12 MHz
• Number Of Programmable I/os: 16
• Number Of Timers: 1
• Maximum Operating Temperature: + 70 C
• Mounting Style: SMD/SMT
• Development Tools By Supplier: CY3654, CY3654-P02
• Minimum Operating Temperature: 0 C
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• Other names: 428-2254-5; CY7C63613C-SXC

Document #: 38-08027 Rev. *B
Table 11.Possible Port Configurations
In “Resistive” mode, a 7-kΩ pull-up resistor is conditionally
enabled for all pins of a GPIO port. The resistor is enabled for
any pin that has been written as a “1.” The resistor is disabled
on any pin that has been written as a “0.” An I/O pin will be
driven high through a 7-kΩ pull-up resistor when a “1” has
been written to the pin. Or the output pin will be driven LOW,
with the pull-up disabled, when a “0” has been written to the
pin. An I/O pin that has been written as a “1” can be used as
an input pin with an integrated 7-kΩ pull-up resistor. Resistive
mode selects a negative (falling edge) interrupt polarity on all
pins that have the GPIO interrupt enabled.
In “CMOS” mode, all pins of the GPIO port are outputs that are
actively driven. The current source and sink capacity are
roughly the same (symmetric output drive). A CMOS port is not
a possible source for interrupts.
A port configured in CMOS mode has interrupt generation
disabled, yet the interrupt mask bits serve to control port
DAC Port
Config Bit 1
Port Configuration bits
Port 3
W
7
Addr: 0x08
11
10
10
01
00
Internal
Data Bus
Config Bit 0
Port 3
W
6
Interrupt
Enable
Interrupt
Polarity
Config Bit 1
Internal
Buffer
Port 2
DAC Write
DAC Read
W
Pin Interrupt Bit
Data
Out
Latch
5
Table 12.GPIO Configuration Register
Figure 5. Block Diagram of DAC Port
X
X
X
0
1
GPIO Configuration Register
Config Bit 0
Isink
Register
Port 2
W
4
4 bits
Isink
DAC
direction. If a port’s associated Interrupt Mask bits are cleared,
those port bits are strictly outputs. If the Interrupt Mask bits are
set then those bits will be open drain inputs. As open drain
inputs, if their data output values are ‘1’ those port pins will be
CMOS inputs (HIGH Z output).
In “Open Drain” mode the internal pull-up resistor and CMOS
driver (HIGH) are both disabled. An I/O pin that has been
written as a “1” can be used as either a high-impedance input
or a three-state output. An I/O pin that has been written as a
“0” will drive the output LOW. The interrupt polarity for an open
drain GPIO port can be selected as either positive (rising
edge) or negative (falling edge).
During reset, all of the bits in the GPIO Configuration Register
are written with “0.” This selects the default configuration:
Open Drain output, positive interrupt polarity for all GPIO
ports.
Config Bit 1
to Interrupt
Controller
Port 1
W
3
CMOS Output
Driver Mode
V
Open Drain
Open Drain
Open Drain
CC
Resistive
Q1
14 KΩ
Config Bit 0
Port 1
W
2
ESD
DAC
I/O Pin
Config Bit 1
Port 0
Interrupt Polarity
W
1
CY7C63413C
CY7C63513C
CY7C63613C
+ (default)
disabled
disabled
-
-
Page 13 of 32
Config Bit 0
Port 0
W
0
[+] Feedback