DSPIC33FJ64MC802-H/MM Microchip Technology, DSPIC33FJ64MC802-H/MM Datasheet - Page 149

• Manufacturer Part Number: DSPIC33FJ64MC802-H/MM
• Description: 16-bit DSC, 64KB Flash, Motor, CAN, DMA, 40 MIPS, NanoWatt 28 QFN-S 6x6mm TUBE
• Manufacturer: Microchip Technology
• Series: dsPIC™ 33Fr

Specifications of DSPIC33FJ64MC802-H/MM

• Core Processor: dsPIC
• Core Size: 16-Bit
• Speed: 20 MIPS
• Connectivity: CAN, I²C, IrDA, LIN, SPI, UART/USART
• Peripherals: Brown-out Detect/Reset, DMA, Motor Control PWM, QEI, POR, PWM, WDT
• Number Of I /o: 21
• Program Memory Size: 64KB (64K x 8)
• Program Memory Type: FLASH
• Ram Size: 16K x 8
• Voltage - Supply (vcc/vdd): 3 V ~ 3.6 V
• Data Converters: A/D 6x10b/12b
• Oscillator Type: Internal
• Operating Temperature: -40°C ~ 140°C
• Package / Case: 28-QFN
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• Eeprom Size: -
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant

REGISTER 9-1:
© 2011 Microchip Technology Inc.
bit 15
bit 7
Legend:
R = Readable bit
-n = Value at POR
bit 15
bit 14-12
bit 11
bit 10-8
bit 7
bit 6
bit 5
bit 4
Note 1:
dsPIC33FJ32MC302/304, dsPIC33FJ64MCX02/X04 AND dsPIC33FJ128MCX02/X04
CLKLOCK
R/W-0
U-0
—
2:
3:
Writes to this register require an unlock sequence. Refer to Section 39. “Oscillator (Part III)” (DS70216)
in the “dsPIC33F/PIC24H Family Reference Manual” (available from the Microchip web site) for details.
Direct clock switches between any primary oscillator mode with PLL and FRCPLL mode are not permitted.
This applies to clock switches in either direction. In these instances, the application must switch to FRC
mode as a transition clock source between the two PLL modes.
This register is reset only on a Power-on Reset (POR).
Unimplemented: Read as ‘0’
COSC<2:0>: Current Oscillator Selection bits (read-only)
111 = Fast RC oscillator (FRC) with Divide-by-n
110 = Fast RC oscillator (FRC) with Divide-by-16
101 = Low-Power RC oscillator (LPRC)
100 = Secondary oscillator (S
011 = Primary oscillator (XT, HS, EC) with PLL
010 = Primary oscillator (XT, HS, EC)
001 = Fast RC oscillator (FRC) with PLL
000 = Fast RC oscillator (FRC)
Unimplemented: Read as ‘0’
NOSC<2:0>: New Oscillator Selection bits
111 = Fast RC oscillator (FRC) with Divide-by-n
110 = Fast RC oscillator (FRC) with Divide-by-16
101 = Low-Power RC oscillator (LPRC)
100 = Secondary oscillator (S
011 = Primary oscillator (XT, HS, EC) with PLL
010 = Primary oscillator (XT, HS, EC)
001 = Fast RC oscillator (FRC) with PLL
000 = Fast RC oscillator (FRC)
CLKLOCK: Clock Lock Enable bit
If clock switching is enabled and FSCM is disabled, (FCKSM<1:0> (FOSC<7:6>) = 0b01)
1 = Clock switching is disabled, system clock source is locked
0 = Clock switching is enabled, system clock source can be modified by clock switching
IOLOCK: Peripheral Pin Select Lock bit
1 = Peripherial pin select is locked, write to peripheral pin select registers not allowed
0 = Peripherial pin select is not locked, write to peripheral pin select registers allowed
LOCK: PLL Lock Status bit (read-only)
1 = Indicates that PLL is in lock, or PLL start-up timer is satisfied
0 = Indicates that PLL is out of lock, start-up timer is in progress or PLL is disabled
Unimplemented: Read as ‘0’
IOLOCK
R/W-0
R-0
OSCCON: OSCILLATOR CONTROL REGISTER
y = Value set from Configuration bits on POR
W = Writable bit
‘1’ = Bit is set
COSC<2:0>
LOCK
R-0
R-0
OSC
OSC
R-0
U-0
)
)
—
(2)
U = Unimplemented bit, read as ‘0’
‘0’ = Bit is cleared
R/C-0
U-0
CF
—
R/W-y
(1,3)
U-0
—
NOSC<2:0>
x = Bit is unknown
LPOSCEN
R/W-y
R/W-0
C = Clear only bit
DS70291E-page 149
(2)
OSWEN
R/W-0
R/W-y
bit 8
bit 0