ATV61HC11Y SQUARE D, ATV61HC11Y Datasheet - Page 2

• Manufacturer Part Number: ATV61HC11Y
• Description: ALTIVAR 61 DRIVE 125 HP 575/690 VOLT
• Manufacturer: SQUARE D

Complementary
Product destination
Power supply voltage limits
Power supply frequency
Power supply frequency limits
Continuous output current
Speed drive output frequency
Speed range
Speed accuracy
Torque accuracy
Transient overtorque
Braking torque
Regulation loop
Motor slip compensation
Diagnostic
Output voltage
Electrical isolation
Type of cable for mounting in an enclosure
Electrical connection
Tightening torque
Supply
Analogue input number
Analogue input type
Sampling time
Absolute accuracy precision
Linearity error
Analogue output number
Analogue output type
2
Asynchronous motors
Synchronous motors
425...759 V
50...60 Hz (- 5...5 %)
47.5...63 Hz
125 A at 2.5 kHz, 575 V 3 phases
125 A at 2.5 kHz, 690 V 3 phases
136 A at 2.5 kHz, 500 V 3 phases
0.1...500 Hz
1...100 in open-loop mode, without speed feedback
+/- 10 % of nominal slip for 0.2 Tn to Tn torque variation without speed feedback
+/- 15 % in open-loop mode, without speed feedback
130 % of nominal motor torque, +/- 10 % for 60 s
<= 125 % with braking resistor
30 % without braking resistor
Frequency PI regulator
Adjustable
Automatic whatever the load
Can be suppressed
Not available in voltage/frequency ratio (2 or 5 points)
1 LED red presence of drive voltage
<= power supply voltage
Between power and control terminals
With an IP21 or an IP31 kit: 3-strand IEC cable at 40 °C, copper 70 °C PVC
With UL Type 1 kit: 3-strand UL 508 cable at 40 °C, copper 75 °C PVC
Without mounting kit: 1-strand IEC cable at 45 °C, copper 70 °C PVC
Without mounting kit: 1-strand IEC cable at 45 °C, copper 90 °C XLPE/EPR
AI1-/AI1+, AI2, AO1, R1A, R1B, R1C, R2A, R2B, LI1...LI6, PWR terminal 2.5
mm² / AWG 14
L1/R, L2/S, L3/T, U/T1, V/T2, W/T3 terminal 2 x 120 mm² / 2 x 250 kcmil
PA, PB terminal 120 mm² / 250 kcmil
PC/-, PA/+ terminal 2 x 120 mm² / 2 x 250 kcmil
AI1-/AI1+, AI2, AO1, R1A, R1B, R1C, R2A, R2B, LI1...LI6, PWR 0.6 N.m
L1/R, L2/S, L3/T, U/T1, V/T2, W/T3 24 N.m / 212 lb.in
PA, PB 24 N.m / 212 lb.in
PC/-, PA/+ 24 N.m / 212 lb.in
External supply 24 V DC (19...30 V), 30 W
Internal supply for reference potentiometer (1 to 10 kOhm) 10.5 V DC +/- 5 %, <=
10 mA for overload and short-circuit protection
Internal supply 24 V DC (21...27 V), <= 200 mA for overload and short-circuit pro-
tection
2
AI1-/Al1+ bipolar differential voltage +/- 10 V DC, input voltage 24 V max, resolu-
tion 11 bits + sign
AI2 software-configurable current 0...20 mA, impedance 242 Ohm, resolution 11
bits
AI2 software-configurable voltage 0...10 V DC, input voltage 24 V max,
impedance 30000 Ohm, resolution 11 bits
Analog input AI1-/Al1+ 2 ms, +/- 0.5 ms
Analog input Al2 2 ms, +/- 0.5 ms
Analog output AO1 2 ms, +/- 0.5 ms
Discrete input LI1...LI5 2 ms, +/- 0.5 ms
Discrete input LI6 (if configured as logic input)2 ms, +/- 0.5 ms
AI1-/Al1+ +/- 0.6 % for a temperature variation 60 °C
AI2 +/- 0.6 % for a temperature variation 60 °C
AO1 +/- 1 % for a temperature variation 60 °C
AI1-/Al1+ +/- 0.15 % of maximum value
AI2 +/- 0.15 % of maximum value
AO1 +/- 0.2 %
1
AO1 software-configurable current, analogue output range 0...20 mA, impedance
500 Ohm, resolution 10 bits
AO1 software-configurable voltage, analogue output range 0...10 V DC,
impedance 470 Ohm, resolution 10 bits
AO1 software-configurable logic output 10 V, <= 20 mA