G3MC-202P DC5 Omron, G3MC-202P DC5 Datasheet - Page 5

• Manufacturer Part Number: G3MC-202P DC5
• Description: SOLID STATE RELAY
• Manufacturer: Omron
• Series: G3MCr

Specifications of G3MC-202P DC5

• Control Voltage Type: DC
• Input Voltage: 4VDC To 6VDC
• Contact Configuration: SPST-NO
• Load Current: 2A
• Load Voltage Range: 75VAC To 264VAC
• Switching Mode: Zero Cross
• Relay Terminals: Through Hole
• Circuit: SPST-NO (1 Form A)
• Output Type: AC, Zero Cross
• Voltage - Input: 4 ~ 6VDC
• Voltage - Load: 75 ~ 264 V
• Mounting Type: Through Hole
• Termination Style: PC Pin
• Package / Case: 4-SIP
• Current, Rating: 2 A
• Function: General Purpose
• Number Of Pins: 4
• Relay Type: Solid State
• Standards: UL, CSA, VDE
• Termination: Solder
• Voltage, Control: 5 VDC
• Voltage, Rating: 240 VAC
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• On-state Resistance: -
• Lead Free Status / Rohs Status: RoHS Compliant part
• Other names: G3MC-202PDC5; G3MC-202PDC5; G3MC202PDC5; Z2985

Precautions
■ General Precautions
Do not touch the terminals of the SSR while power is being supplied
to the SSR. The terminals are charged with the power,
and an electric shock may be received by touching the terminals.
The built-in capacitor may have a residual voltage after the SSR
is turned off. Be sure to discharge the residual voltage before touch-
ing the terminals of the SSR, otherwise an electric shock
may be received.
■ Mounting
1. Make sure that no excessive voltage or current is imposed on or
2. Solder the terminals of the SSR properly under the required sol-
3. Do not short-circuit the load of the SSR while power is supplied to
■ Correct use
The terminals of the SSR are highly heat-conductive. Each terminal
must be soldered within 10 s at 260°C or within 5 s at 350°C.
The SSR is of a thin-profile construction. To maintain the vibration
resistance of the SSR, make sure that the space between the SSR
and PCB is 0.1 mm maximum. Lifting of the PCB can be prevented
by setting the hole diameter of the PCBs on both sides slightly
smaller than the actual terminal dimension.
Select the model without the zero-cross function when using the Unit
for phase control output.
The casing works as a heat sink. When mounting two or more Units
closely, make sure that the Units are properly ventilated by taking
ambient temperature rises into consideration. If Units are closely
mounted and used in places with no ventilation, the load current of
each Unit must be 1/2 of the rated load current.
flows to the input or output circuit of the SSR,
otherwise the SSR may malfunction or burn.
dering conditions. The SSR may be abnormally heated and burn
if power is supplied to the terminals soldered incorrectly.
the SSR. Do not short-circuit the power supply through the SSR.
The SSR may be damaged, malfunction, or burn if the load or
power supply is short-circuited.
■ Protective element
No overvoltage absorption element is built in. Therefore, if the G3MC
is connected to an inductive load, be sure to connect the overvoltage
absorption element.
G3MC-@@@PL (without Zero cross function)
G3MC-@@@P (with Zero cross function)
Input
Input
Phototriac
Phototriac
Solid State Relay
G3MC
Protective
element
(MOV)
Protective
element
(MOV)
Load
Load
Power
supply
Power
supply
381