XS2M-D423 Omron, XS2M-D423 Datasheet - Page 29

• Manufacturer Part Number: XS2M-D423
• Description: CONNECTOR
• Manufacturer: Omron
• Series: XS2r

Specifications of XS2M-D423

• Connector Type: Plug, Male Pins
• Number Of Positions: 4
• Mounting Type: Panel Mount, Flange
• Termination: Solder Cup
• Fastening Type: Threaded
• Orientation: Keyed
• Ingress Protection: IP67 - Dust Tight, Waterproof
• Shell Material, Finish: Brass, Nickel Plated
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• Features: -
• Shell Size - Insert: -
• Shell Size, Military: -
• Lead Free Status / Rohs Status: Lead free / RoHS Compliant
• Other names: XS2MD423

(5) Mounting Cap
Note: If the cap is not tighten securely enough, the degree of protection (IP67)
(6) After Assembly
Recommended Cables
When connecting a commercially available cable to a
connector assembly, use a cable with an outside diameter of
3 to 6 mm and core sizes of 0.18 to 0.75 mm
connectors and 0.5 mm
Connector Arrangement
For safety, when constructing a connection system between a
Sensor and panel with a connector, make sure that the
connector plug is on the Sensor side and the connector socket
is on the panel side (i.e., the female pins are located on the
power-supply side).
For 6-mm-dia. cable
For 4-mm-dia. cable
For 3-mm-dia. cable
Align the triangular marks on the pin block and cover and
insert the pin block into the cover.
Press them together firmly (0.39 to 0.49 N·m) until the pin
block does not come out of the cover.
After mounting the cover to the pin block and the cover
snaps into place, tighten the cap securely by hand within a
torque of 0.39 and 0.49 N·m.
After fully tightening the cap, length A should be
approximately one of the following according to the cable
external diameter and the Connector model.
Confirm the insulation between cores after completing
assembly.
Sensor Side
(Plug)
Pin Block
(Screw-mounting Connectors)
may not be maintained or vibration may cause the cap to become loose.
Do not tighten the cap with pliers or similar tools; they may damage the
cap.
Connector
Cover lock
(Socket)
Connecting Cable
Triangle mark
Pin block
2
maximum for soldering connectors.
6 mm
Cable external diameter (mm)
—
—
1
Cover
(Plug)
A
5 mm
—
0
2
Cap
Panel Side
(Power-supply Side)
4 mm
2
—
1
2
for crimping
(Socket)
3 mm
—
—
1
Safety Precautions
Do not use the product in atmospheres or environments that
exceed product ratings.
Tightening Cap (Connector Assemblies)
1. Do not use pliers to tighten caps, otherwise the caps may
2. If caps are not tightened securely, the Connectors may not
Connector Connection and Disconnection
Degree of Protection
Setup
When connecting or disconnecting Connectors, be sure to
hold the Connectors by hand.
Do not hold the cable part when disconnecting Connectors.
Connectors mating with sockets must be fully inserted into
the sockets. Tighten the thread bracket carefully so that the
threads will not be damaged.
Fully tighten thread bracket within a torque range between
0.39 and 0.49 N·m and be sure that the threads of the
opposite parts are hidden by the thread bracket.
When disconnecting Connectors, be sure to loosen the
thread brackets first. Do not loosen the caps.
Thread brackets must be loosened in the cutout direction.
Do not impose external force continuously on the joints of
pin blocks and covers, otherwise the Connectors may not
keep its proper degree of protection (i.e., IP67).
The degree of protection of connectors (IP67) is not for a
fully watertight structure. Do not use them underwater.
Connectors are of resin mold construction. Do not impose
excessive force on them.
Do not make any cable bends near the base of the Unit.
Any bends made must have a minimum radius of 40 mm.
be damaged. Be sure to tighten each cap by hand within a
torque range between 0.39 and 0.49 N·m.
maintain their proper degree of protection (i.e., IP67) or the
caps may become loose due to vibration.
Precautions for Correct Use
Loosen
Thread
bracket
Cutout
XS2
29