CS1W-V680C11 Omron, CS1W-V680C11 Datasheet - Page 29

• Manufacturer Part Number: CS1W-V680C11
• Description: CS1 1-Head V680 RFID Module
• Manufacturer: Omron

Specifications of CS1W-V680C11

• Lead Free Status / Rohs Status: Lead free / RoHS Compliant

Note: 1. Immediate refreshing cannot be used in the CS1D-CPU@@H/P CPU Units. (It can be used in the CS1D-CPU@@S CPU Units.)
Task Flags
Trace Memory
File Memory
Func-
tions
2. Use a replacement battery that was manufactured within the last two years.
Parallel Processing Mode
Battery-free operation
Constant cycle time
Cycle time monitoring
I/O refreshing
I/O memory holding when
changing operating modes
Load OFF
Input response time setting
Startup mode setting
Memory Card functions
Filing
Debugging
Online editing
Program protection
Error check
Error log
Serial communications
Clock
Power OFF detection time
Power OFF detection delay
time
Memory retention during
power interruptions
Power OFF detection delay
time
Remote programming and
monitoring
Multiple-level
communications
Storing comments in CPU
Unit
Program check
Control output signals
Battery service life
Self-diagnostics
Other functions
Item
32 (TK0000 to TK0031)
Task Flags are read-only flags that are ON when the corresponding cyclic task is executable and OFF when the
corresponding task is not executable or in standby status.
4,000 words (The maximum amount of data that can be traced in a data trace is 500 samples for 31 bits and 6 words.
Memory Cards: A 128MB OMRON Memory Card can be used (MS-DOS format).
EM file memory: The EM Area can be converted to file memory (MS-DOS format).
Program execution and peripheral servicing can be performed simultaneously (CS1D-CPU@@S only).
The user program and the system’s parameters are backed up automatically in flash memory, which is standard
equipment.
1 to 32,000 ms (Unit: 1 ms)
Possible (Unit stops operating if the cycle is too long): 10 to 40,000 ms (Unit: 10 ms)
Cyclic refreshing, immediate refreshing (See note 1.), refreshing with I/O REFRESH instruction
Possible (Depends on the ON/OFF status of the IOM Hold Bit in the Auxiliary Area.)
All outputs on Output Units can be turned OFF.
Time constants can be set for inputs from Basic I/O Units.
The time constant can be increased to reduce the influence of noise and chattering or it can be decreased to detect shorter
pulses on the inputs (CS1 Basic I/O Units only).
Supported.
Automatically reading programs (autoboot) from the Memory Card when the power is turned ON.
Format in which data is stored in Memory
Card
Functions for which Memory Card read/write
is supported
Memory Card data and the EM (Extended Data Memory) Area can be handled as files.
Control set/reset, differential monitoring, data tracing (scheduled, each cycle, or when instruction is executed), storing
location generating error when a program error occurs
User programs can be overwritten in program-block units when the CPU Unit is in MONITOR or PROGRAM mode.
This function is not available for block programming areas.
Overwrite protection: Set using DIP switch.
Copy protection: Password set using Programming Device.
User-defined errors (i.e., user can define fatal errors and non-fatal errors)
The FPD(269) instruction can be used to check the execution time and logic of each programming block.
Up to 20 errors are stored in the error log. Information includes the error code, error details, and the time the error
occurred.
Built-in peripheral port: Programming Device (including Programming Console) connections, Host Links, NT Links
Built-in RS-232C port: Programming Device (excluding Programming Console) connections, Host Links, no-protocol
communications, NT Links
Provided on all models.
Note: Used to store the time when power is turned ON and when errors occur.
10 to 25 ms (not fixed)
0 to 10 ms (user-defined, default: 0 ms)
Held Areas: Holding bits, contents of Data Memory and Extended Data Memory, and status of the counter Completion
Flags and present values.
Note: If the IOM Hold Bit in the Auxiliary Area is turned ON, and the PLC Setup is set to maintain the IOM Hold Bit status
FINS commands can be sent to a computer connected via the Host Link System by executing Network Communications
Instructions from the PLC.
Host Link communications can be used for remote programming and remote monitoring through a Controller Link System
or Ethernet network.
Duplex CPU Systems: 3 levels
Single CPU Systems: 8 levels
Note: Communications are possible across up to eight levels only for the Controller Link and Ethernet networks (and the
I/O comments can be stored in the CPU Unit in Memory Cards or EM file memory.
Program checks are performed at the beginning of operation for items such as no END instruction and instruction errors.
RUN output: The internal contacts will be ON (closed) while the CPU Unit is operating in RUN mode or MONITOR mode.
These terminals are provided only on CS1D-PA207R Power Supply Units.
The battery life is 5 years at an ambient temperature of 25 ° C, although the lifetime can be as short as 1.1 years under
adverse temperature and power conditions. (Battery Set: CS1W-BAT01) (See note 2.)
CPU errors (watchdog timer), I/O verification errors, I/O bus errors, memory errors, and battery errors
Words in the Auxiliary Area store the number of power interruptions, time of the last power interruption, and total power
ON time.
when power to the PLC is turned ON, the contents of the CIO Area, the Work Area, part of the Auxiliary Area, timer
Completion Flags and PVs, Index Registers, and the Data Registers will be saved.
CX-Integrator or CX-Net in CX-Programmer version 4.0 or higher is required to set the routing tables).
Communications are possible across only up to three communications levels for the SYSMAC LINK, DeviceNet,
and FL-net networks.
Programmable Controllers SYSMAC
User program: Program file format
PLC Setup and other parameters: Data file format (binary format)
I/O memory: Data file format (binary format), text format, or CSV format
User program instructions, Programming Devices (including Programming
Consoles), Host Link computers
Specifications
CS1D
35