A3DT-5201 Omron, A3DT-5201 Datasheet
A3DT-5201
Specifications of A3DT-5201
A3DT5201NC
Related parts for A3DT-5201
A3DT-5201 Summary of contents
Page 1
... (1) Shape of Pushbutton Symbol Shape J Rectangular A Square T Round List of Models Appearance Rectangular A3DJ Square A3DA Round A3DT 20 (2) (2) Switch Specifications Microload (30 VDC, 0.1 A) Symbol Terminals Operation Contact A Momentary Solder SPST-NO B Alternate Minimum applicable load VDC Standard load models are not available. If PCB terminals are required, use the Socket given under Accessories on page 22 ...
Page 2
... Appearance Degree of protection A3DJ (Rectangular) IP40 A3DA (Square) A3DT (Round) 9 dia. Note: 1. Enter the desired color symbol for the Pushbutton All the above are solder-terminal, microload, SPST-NO, LED lamp-lighted models. Ordering Individually Pushbuttons and Switches can be ordered separately. Combinations that are not available as sets can be created using individual Units. Also, store the parts as spares for maintenance and repairs ...
Page 3
... Solder terminals A3DJ-7121 Classification Wire-wrap terminal A3D-4101 PCB terminal A3D-4102 Solder terminal A3D-4103 --- A3D-3002 --- A3D-3004 Rectangular A3DJ-5201 Square A3DA-5201 Round A3DT-5201 A3D Round A3DT-500R A3DT-500Y A3DT-500GY A3DT-500W IP40 Square Round A3DA-7111 A3DT-7111 A3DA-7121 A3DT-7121 Model Application precautions Cannot be used together with Insulation Cover. ...
Page 4
A3D Specifications Ratings Contact Rating: 30 VDC, 0.1 A (Minimum Appli- cable Load: 5 VDC, 1 mA) The above ratings conform to JIS C4505, for testing under the fol- lowing conditions. Built-in LED Lamp Item Forward voltage ...
Page 5
A3D Operating Characteristics OF max. 2. min. 0.196 N TT Approx. 3.5 mm LTA min. (See note.) 0 max. 2.5 mm Note: The figure for LTA in the table applies only to models with alternate operation. ...
Page 6
... Shape of Pushbutton Rectangular (A3DJ) Square (A3DA) Switch Switch Specifications Microload 0 VDC Minimum applicable load VDC Round (A3DT) Note: The A3DJ model is shown here as a representative example. A3D Color cap Legend plate (milky white) Reflective plunger LED Color of Pushbutton (All models LED-lighted) ...
Page 7
... Note: Recommended panel thickness: 1.0 to 3.2 mm. PCB Terminal A3D-4102 9 dia. PCB Cutout (bottom view) Four, 0.8 dia. A3D Square models (A3DA) and round models (A3DT) 10 min. +0.2 8 dia min. Note: Recommended panel thickness: 1.0 to 3.2 mm. Solder Terminal A3D-4103 9 dia. ...
Page 8
... After wiring is completed, mount the Insulation Cover by pushing it into the Switch. Round A3DT-5201 5.8 dia. If soldering is used, mount the mounting nut first. Lead wires and mounds of solder may make it impossible to mount the nut after sol- dering. ...
Page 9
A3D Precautions Refer to the Common Precautions for Pushbutton Switches on page 14. Correct Use Mounting Always make sure that the power is turned OFF before mounting, removing, or wiring the Switch, or performing maintenance. Do not tighten the mounting ...