XS5F-D421-C80-A Omron, XS5F-D421-C80-A Datasheet - Page 14

• Manufacturer Part Number: XS5F-D421-C80-A
• Description: Sensor I/O Connector
• Manufacturer: Omron
• Series: M12 Seriesr

Specifications of XS5F-D421-C80-A

• Product Type: Connectors
• Contact Style: Socket (Female)
• Shell Style: Receptacle
• Number Of Contacts: 4
• Mounting Style: Threaded
• Termination Style: Quick Connect
• Current Rating: 4 A
• Voltage Rating: 250 VAC
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant

Assembly Procedure for XS5C/XS5G Connector Assemblies
(1) Connector and Cable External Diameters
Note: When connecting a commercially available cable to a
(2) Component Insertion
• Connectors for 6-, 4-, and 3-mm-diameter Cables (i.e., Cables that
• Connectors for 6-mm-diameter Cables use white cable clamps.
Crimping/Soldering Connectors
Straight Connectors
Angled Connectors
• As shown in the above illustration, connect the above components
Screw-on Connectors
Confirm that you have all of the required parts.
Insulation caps and insulation tubes are included with
5-pole Connectors (XS2C-D5S@ and XS2G-D5S@).
are 5 to 6, 4 to 5, and 3 to 4 mm in diameter respectively) are
available. When assembling a Connector used with a cable, make
sure that the external diameter of the Connector is suited to that of
the cable.
Connectors for 4- and 3-mm-diameter Cables use black cable
clamps.
A watertight bushing for 6-mm-diameter Cable has no stripe, that
for 4-mm-diameter Cable has a single stripe, and that for 3-mm-
diameter Cable has two stripes.
to the Cable with its end processed.
*1. Rings are not required with 7-mm and 8-mm cables.
*2. Insert the waterproof bushing for 7-mm and 8-mm
connector assembly, use a cable with an outside diameter of 3
to 6 mm and core sizes of 0.18 to 0.75 mm
connectors and 0.5 mm
cables in the direction shown in the diagram.
* A ring is not required for Screw-on Connectors.
Cover
Cover
Cover
Cover
Ring *1
Watertight
Ring (Angled models only) *
bushing
2
Watertight
bushing
maximum for soldering connectors.
Watertight
bushing
Watertight bushing
Cable clamp
Cable clamp
Cable
clamp
Cable clamp
Cap
Cap
2
(
Cap
*2
for crimping
Cap
)
(3) Wiring (Processing Cable Ends)
Crimping
Wiring
• Strip 10 mm of the Cable sheath and 4 mm of each core.
• Before soldering cores and solder cup pins together, solder-coat
• The following conditions are recommended for soldering each
• The length marked *A should be 6.5 mm max., otherwise the
• Strip 14 mm of the Cable sheath and 4 mm of each core.
• Make sure that each core is not damaged and its end strands are
• Mount the XY2F-0003 Locator to XY2F-0002 Crimping Tool, both
• After mounting the crimping pins to the Locator, fully insert the
• Squeeze the handle of the Crimp Tool to press-fit the cores to the
• After press-fitting the cores to the pins, insert the pins into the pin
Soldering Connectors
Crimping Connectors
each of them.
solder cup pin.
proper degree of protection of the connector will not be maintained.
not spread out.
of which are sold separately, and set the selector dial of the
Crimping Tool to 6 for the XS5U-@@21 and to 7 for the XS5U-
@@22.
cores to the crimping pins.
crimping pins.
(Squeeze the handle firmly until the handle automatically returns to
the release position.)
clamp as shown in the illustration. Then make sure that the lead
colors correspond to the pin clamp numbers that are identical to
the connector pin numbers.
Soldering iron: 30 to 60 W
Soldering temperature: 280°C to 340°C
Soldering period: 3 s max.
Pin clamp
Press
6
±0.5
1 to 1.5
*A
XS5
14