DS12CR887-5 Maxim Integrated Products, DS12CR887-5 Datasheet - Page 9

• Manufacturer Part Number: DS12CR887-5
• Description: Real Time Clock
• Manufacturer: Maxim Integrated Products

Specifications of DS12CR887-5

• Function: Clock, Calendar
• Rtc Memory Size: 114 B
• Supply Voltage (max): 5.5 V
• Supply Voltage (min): 4.5 V
• Maximum Operating Temperature: + 85 C
• Minimum Operating Temperature: - 40 C
• Mounting Style: Through Hole
• Rtc Bus Interface: Multiplexed
• Package / Case: eDIP
• Time Format: HH:MM:SS, Binary
• Date Format: DW:DM:M:Y, Binary
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant

PDIP
SO,
22
17
18
16, 20,
21, 22
EDIP
2, 3,
17
18
PIN
13, 18,
PLCC
1, 11,
26
21
22
4, 6, 10,
15, 20,
23, 25,
27, 32
TQFP
18
19
RESET
NAME
N.C.
DS
_____________________________________________________________________
No Connection. This pin should remain unconnected. Pin 21 is RCLR for the
DS12887A/DS12C887A. On the EDIP, these pins are missing by design.
D ata S tr ob e or Read Inp ut. The D S p i n has tw o m od es of op er ati on d ep end i ng on
the l evel of the M O T p i n. W hen the M O T p i n i s connected to V
ti m i ng i s sel ected . In thi s m od e, D S i s a p osi ti ve p ul se d ur i ng the l atter p or ti on of the
b us cycl e and i s cal l ed d ata str ob e. D ur i ng r ead cycl es, D S si g ni fi es the ti m e that the
device i s to d r i ve the b i d i r ecti onal b us. In w r i te cycl es, the tr ai l i ng ed g e of D S causes
the device to l atch the w r i tten d ata. W hen the M O T p i n i s connected to GN D , Intel
b us ti m i ng i s sel ected . D S i d enti fi es the ti m e p er i od w hen the device d r i ves the b us
w i th r ead d ata. In thi s m od e, the D S p i n op er ates i n a si m i l ar fashi on as the outp ut-
enab l e ( O E ) si g nal on a g ener i c RAM .
Active-Low Reset Input. The RESET pin has no effect on the clock, calendar, or
RAM. On power-up, the RESET pin can be held low for a time to allow the power
supply to stabilize. The amount of time that RESET is held low is dependent on the
application. However, if RESET is used on power-up, the time RESET is low should
exceed 200ms to ensure that the internal timer that controls the device on power-
up has timed out. When RESET is low and V
In a typical application, RESET can be connected to V
the device to go in and out of power fail without affecting any of the control
registers.
A. Periodic interrupt-enable (PIE) bit is cleared to 0.
B. Alarm interrupt-enable (AIE) bit is cleared to 0.
C. Update-ended interrupt-enable (UIE) bit is cleared to 0.
D. Periodic-interrupt flag (PF) bit is cleared to 0.
E. Alarm-interrupt flag (AF) bit is cleared to 0.
F. Update-ended interrupt flag (UF) bit is cleared to 0.
G. Interrupt-request status flag (IRQF) bit is cleared to 0.
H. IRQ pin is in the high-impedance state.
I. The device is not accessible until RESET is returned high.
J. Square-wave output-enable (SQWE) bit is cleared to 0.
Pin Description (continued)
Real-Time Clocks
FUNCTION
CC
is above V
CC
. This connection allows
PF
C C
, the following occurs:
, M otor ol a b us
9