PXC10VC82RMF60TP United Chemi-Con, PXC10VC82RMF60TP Datasheet - Page 2

• Manufacturer Part Number: PXC10VC82RMF60TP
• Manufacturer: United Chemi-Con
• Type: Polymerr

Specifications of PXC10VC82RMF60TP

• Tolerance (+ Or -): 20%
• Voltage: 10VDC
• Esr: 23mOhm
• Mounting Style: Surface Mount
• Construction: Cylindrical
• Lifetime: 1000
• Product Diameter (mm): 6.3mm
• Product Height (mm): 5.7mm
• Product Depth (mm): Not Requiredmm
• Product Length (mm): Not Requiredmm
• Seated Plane Height: Not Requiredmm
• Lead Spacing (nom): Not Requiredmm
• Lead Diameter (nom): Not Requiredmm
• Operating Temp Range: -55C to 105C
• Capacitance: 82uF
• Ripple Current: 2.4A
• Lead Free Status / RoHS Status: Supplier Unconfirmed

PXC Series
PXC Specifications
Part Numbering System for PXC Series
2 /4
Category Temperature Range
Rated Voltage Range
Capacitance Range
Capacitance Tolerance
Leakage Current
Dissipation Factor ( Tan )
Low Temperature
Characteristics
Endurance
(Load Life )
Bias Humidity Test
Surge Voltage Test
Failure Rate
PXC
United Chemi-Con, Inc. 9801 W. Higgins Road, Rosemont, IL 60018 Tel [phone] Fax [phone] www.chemi-con.com
2.5
Item
VC
181
M
2.5 to 16VDC
27 to 470 F
I
Note: If you need to measure the leakage current, apply a voltage treatment by subjecting the
capacitors to the DC rated voltage for 120 minutes at 105 C before the measurement.
Where I = Max. leakage current ( A ), C = Nominal capacitance ( F ) and V = Rated voltage ( V )
0.12 maximum at
At 100kHz, impedance ( Z ) ratio between the
not exceed the values given below.
The following specifications shall be satisfied when the capacitors are restored to 20 C after
subjecting them to the DC rated voltage for 1,000 hours at 105 C.
Appearance
Capacitance change: ≤
Tan
ESR
Leakage current
The following specifications shall be satisfied when the capacitors are restored to 20 C after
subjecting them to the DC rated voltage for 500 hours at
Appearance
Capacitance change: ≤
Tan
ESR
Leakage current
The following specifications shall be satisfied when the capacitors are restored to 20 C after
the surge voltage is applied at 105 C through a protective resistor of 1,000 ohms at a cycling
of 30 seconds on, 5.5 minutes off for 1,000 cycles. The surge voltage shall not exceed 115%
of the rated voltage.
Appearance
Capacitance change: ≤
Tan
ESR
Leakage current
1% maximum per 1,000 hours at 105 C with rated voltage applied. (Confidence level 60%)
E60
Rated Voltage ( V )
Z ( 25 C ) / Z ( 20 C )
Z ( 55 C ) / Z ( 20 C )
55 to 105 C
20% ( M ) at
0.2CV maximum after 2 minutes at
( DF )
( DF )
( DF )
TP
20 C, 120Hz
When ordering, always specify complete catalog number for PXC Series.
20 C, 120Hz
: no significant damage
: ≤ 150% of the initial specified value
: ≤ 150% of the initial specified value
: ≤ initial specified value
: no significant damage
: ≤ 150% of the initial specified value
: ≤ 150% of the initial specified value
: ≤ initial specified value
: no significant damage
: ≤ 150% of the initial specified value
: ≤ 150% of the initial specified value
: ≤ initial specified value
Packaging: TP = Standard Taping.
Case Code: See Case Sizes in Tables.
Capacitance Tolerance: M =
Capacitance Value: Expressed in Microfarads. The first two digits are
significant figures, and the third digit indicates the number of zeros
for capacitance of 100 F or more. R indicates the decimal point for
capacitance less than 100 F (e.g. R18 = .18 F; 1R8 = 1.8 F;
18R = 18 F; 181 = 180 F; 182 = 1,800 F; 183 = 18,000 F ).
Lead Configuration: VC = Vertical Chip, 2 SMD Terminals.
DC Rated Voltage: Expressed in Volts (e.g. 2.5 = 2.5WVDC).
Series Name: Indicates Basic Capacitor Design.
2.5 -16
≤ 1.15
≤ 1.25
20% of the initial measured value
20% of the initial measured value
20% of the initial measured value
Characteristics
20 C.
25 C or
20%
55 C value and
60 C, 90 - 95%RH.
Engineering Bulletin Jul 03
20 C value shall