FTLX1612M3BCL Finisar Corporation, FTLX1612M3BCL Datasheet
FTLX1612M3BCL
Specifications of FTLX1612M3BCL
Available stocks
Related parts for FTLX1612M3BCL
FTLX1612M3BCL Summary of contents
Page 1
... Built-in digital diagnostic functions • Commercial temperature range: -5°C to 75°C Finisar’s 40km FTLX1612M3BCL Small Form Factor 10Gb/s XFP transceivers comply with the current XFP Multi-Source Agreement (MSA) Specification with SONET OC-192 IR-2, OC-192 IR-3, SDH STM S-64.2b, STM S-64.3b as well as with 10-Gigabit Ethernet 10GBASE-ER/EW per IEEE 802 ...
Page 2
... FTLX1612M3BCL 40km XFP Product Specification – November 2009 I. Pin Descriptions Pin Logic Symbol 1 GND 2 VEE5 3 LVTTL-I Mod-Desel 4 LVTTL-O Interrupt 5 LVTTL-I TX_DIS 6 VCC5 7 GND 8 VCC3 9 VCC3 10 LVTTL-I SCL 11 LVTTL- SDA I/O 12 LVTTL-O Mod_Abs 13 LVTTL-O Mod_NR 14 LVTTL-O RX_LOS 15 GND 16 GND 17 CML-O RD- 18 CML-O ...
Page 3
... FTLX1612M3BCL 40km XFP Product Specification – November 2009 Diagram of Host Board Connector Block Pin Numbers and Names II. Absolute Maximum Ratings Parameter Maximum Supply Voltage 1 Maximum Supply Voltage 2 Storage Temperature Case Operating Temperature © Finisar Corporation 30-November-2009 Rev B2 Symbol Min Typ Vcc3 -0 ...
Page 4
... FTLX1612M3BCL 40km XFP Product Specification – November 2009 III. Electrical Characteristics Parameter Main Supply Voltage Supply Voltage #2 Supply Current – Vcc5 supply Supply Current – Vcc3 supply Module total power Transmitter Input differential impedance Differential data input swing Transmit Disable Voltage ...
Page 5
... FTLX1612M3BCL 40km XFP Product Specification – November 2009 IV. Optical Characteristics Please note that the Transmitter of the FTLX1612M3BCL becomes operational within 5 seconds of power-up. This is due to the time required for the EML to reach its optimum operating temperature. Parameter Transmitter Output Opt. Pwr: 9/125 SMF ...
Page 6
... Tested with a 2 – 1 PRBS 3. The FTLX1612M3BCL can support 8.5Gb/s Fibre-Channel with the transceiver CDRs placed in “by- pass” mode. CDR-bypass mode can be achieved by changing the register value in EEPROM-Table 0, Byte 111, Bit 0. Use bit 111.0 to enable/disable Rx CDR (“1” to bypass and “0” to engage default, the CDR devices shall be engaged on power cycle or module reset ...
Page 7
... FTLX1612M3BCL 40km XFP Product Specification – November 2009 VIII. Digital Diagnostics Functions 1 As defined by the XFP MSA , Finisar XFP transceivers provide digital diagnostic functions via a 2-wire serial interface, which allows real-time access to the following operating parameters: • Transceiver temperature • Laser bias current • ...
Page 8
... FTLX1612M3BCL 40km XFP Product Specification – November 2009 IX. Mechanical Specifications Finisar’s XFP transceivers are compliant with the dimensions defined by the XFP Multi- Sourcing Agreement (MSA). 77.95 22.15 13.30 1.95 16.00 20.85 39.00 XFP Transceiver (dimensions are in mm) © Finisar Corporation 30-November-2009 Rev ...
Page 9
... FTLX1612M3BCL 40km XFP Product Specification – November 2009 X. PCB Layout and Bezel Recommendations XFP Host Board Mechanical Layout (dimensions are in mm) © Finisar Corporation 30-November-2009 Rev Page 9 ...
Page 10
... FTLX1612M3BCL 40km XFP Product Specification – November 2009 XFP Detail Host Board Mechanical Layout (dimensions are in mm) © Finisar Corporation 30-November-2009 Rev Page 10 ...
Page 11
... FTLX1612M3BCL 40km XFP Product Specification – November 2009 XFP Recommended Bezel Design (dimensions are in mm) © Finisar Corporation 30-November-2009 Rev Page 11 ...
Page 12
... FTLX1612M3BCL 40km XFP Product Specification – November 2009 XI. References 1. 10 Gigabit Small Form Factor Pluggable Module (XFP) Multi-Source Agreement (MSA), Rev 4.5 – August 2005. Documentation is currently available at http://www.xfpmsa.org/ 2. Application Note AN-2035: “Digital Diagnostic Monitoring Interface for XFP Optical Transceivers” – Finisar Corporation, December 2003 3 ...