MAX2839ETN+ Maxim Integrated Products, MAX2839ETN+ Datasheet - Page 5

• Manufacturer Part Number: MAX2839ETN+
• Description: RF Transceiver 2.3Ghz To 2.7Ghz MIM O Wireless Broadband
• Manufacturer: Maxim Integrated Products

Specifications of MAX2839ETN+

• Lead Free Status / RoHS Status: Lead free / RoHS Compliant

AC ELECTRICAL CHARACTERISTICS TABLE—Rx MODE (continued)
(MAX2839 Evaluation Kit, V
f
applications circuit and registers set to default settings and corresponding test mode, unless otherwise noted. Lowpass filter is set to
10MHz RF channel BW. Unmodulated single tone RF input signal is used with specifications which normally apply over the entire
operating conditions, unless otherwise indicated.) (Note 1)
REF
RF Channel BW Supported by
Baseband Filter
Baseband Gain Ripple
Baseband Group Delay Ripple
Baseband Filter Rejection for
5MHz RF Channel BW
Baseband Filter Rejection for
10MHz RF Channel BW
RSSI
RSSI Minimum Output Voltage
RSSI Maximum Output Voltage
RSSI Slope
RSSI Output Settling Time
= 40MHz, ENABLE = RXTX = CS = high, SCLK = DIN = low, with power matching for the differential RF pins using the typical
2.3GHz to 2.7GHz MIMO Wireless Broadband
PARAMETER
_______________________________________________________________________________________
CC_
= 2.8V, T
A4:A0 = 00100 serial bits D9:D6 = 0000
A4:A0 = 00100 serial bits D9:D6 = 0001
A4:A0 = 00100 serial bits D9:D6 = 0010
A4:A0 = 00100 serial bits D9:D6 = 0011
A4:A0 = 00100 serial bits D9:D6 = 0100
A4:A0 = 00100 serial bits D9:D6 = 0101
A4:A0 = 00100 serial bits D9:D6 = 0110
A4:A0 = 00100 serial bits D9:D6 = 0111
A4:A0 = 00100 serial bits D9:D6 = 1000
A4:A0 = 00100 serial bits D9:D6 = 1001
A4:A0 = 00100 serial bits D9:D6 = 1010
A4:A0 = 00100 serial bits D9:D6 = 1011
A4:A0 = 00100 serial bits D9:D6 = 1100
A4:A0 = 00100 serial bits D9:D6 = 1101
A4:A0 = 00100 serial bits D9:D6 = 1110
A4:A0 = 00100 serial bits D9:D6 = 1111
0 to 2.3MHz for BW = 5MHz
0 to 4.6MHz for BW = 10MHz
0 to 2.3MHz for BW = 5MHz
0 to 4.6MHz for BW = 10MHz
At 3.3MHz
At > 21MHz
At 6.7MHz
At > 41.6MHz
R
R
To within 3dB of steady state
LOAD
LOAD
A
= +25°C, f
≥ 10kΩ
≥ 10kΩ
RF
= 2.4999GHz, f
CONDITIONS
LO
+32dB signal step
-32dB signal step
= 2.5GHz; baseband output signal frequency = 100kHz,
RF Transceiver
MIN
TYP
1.75
2.25
10.0
12.0
14.0
15.0
20.0
24.0
28.0
200
800
0.4
2.2
3.5
5.0
5.5
6.0
7.0
8.0
9.0
1.3
1.3
30
90
50
85
85
6
6
MAX
UNITS
mV/dB
dB
ns
MHz
dB
dB
ns
V
V
P-P
P-P
5