UPC2709TB NEC, UPC2709TB Datasheet

Page 1

... PART NUMBER PC2709TB-E3 6-pin super minimold Remark To order evaluation samples, please contact your local NEC sales office. (Part number for sample order: PC2709TB) The information in this document is subject to change without notice. Before using this document, please confirm that this is the latest version. ...

Page 2

... PIN CONNECTIONS (Top View PRODUCT LINE-UP OF PC2709 ( (sat) PART NO. (GHz) (dBm) PC2709T 2.3 +11.5 PC2709TB Remark Typical performance. Please refer to ELECTRICAL CHARACTERISTICS in detail. Caution The package size distinguishes between minimold and super minimold. 2 (Bottom View +25° 5 out (dB) (dB) (mA Data Sheet P12653EJ2V1DS00 PC2709TB Pin NO ...

Page 3

SYSTEM APPLICATION EXAMPLE EXAMPLE OF DBS CONVERTERS BS Antenna (DBS ODU) Parabola Antenna EXAMPLE OF 900 MHz BAND, 1.5 GHz BAND DIGITAL CELLULAR TELEPHONE RX SW Driver TX PA PC2709TB To know the associated products, please refer to each latest ...

Page 4

... Ground pin. This pin should be connected to system ground with minimum inductance. Ground pattern on the board should be formed as wide as possible. All the ground pins must be con- nected together with wide ground pattern to decrease impedance defference. = 5.0 V Data Sheet P12653EJ2V1DS00 PC2709TB Internal equivalent circuit ...

Page 5

ABSOLUTE MAXIMUM RATINGS PARAMETER SYMBOL Supply Voltage V CC Total Circuit Current I CC Power Dissipation P D Operating Ambient Temperature T A Storage Temperature T stg Input Power P in RECOMMENDED OPERATING CONDITIONS PARAMETER SYMBOL Supply Voltage V CC ...

Page 6

... V fluctuation. CC The coupling capacitors, connected to the input and output pins, are used to cut the DC and minimize RF serial impedance. Their capacitance are therefore selected as lower impedance against a 50 perform as high pass filters, suppressing low frequencies to DC. To obtain a flat gain from 100 MHz upwards, 1 000 pF capacitors are used in the test circuit. In the case of under 10 MHz operation, increase the value of coupling capacitor such as 10 000 pF ...

Page 7

Illustration of the test circuit assembled on evaluation board Top View Mounting direction Component List Value C 1 000 pF L 300 nH AMP Notes 0.4 mm double sided copper clad polyimide ...

Page 8

TYPICAL CHARACTERISTICS (T CIRCUIT CURRENT vs. SUPPLY VOLTAGE Supply Voltage - V CC NOISE FIGURE AND INSERTION POWER GAIN vs. FREQUENCY 8 30 5.0 V ...

Page 9

OUTPUT POWER vs. INPUT POWER + 1.0 GHz 5 –5 –10 –15 –20 –35 –30 –25 –20 –15 –10 – Input Power - dBm ...

Page 10

S-Parameter ( -FREQUENCY 11 S -FREQUENCY 22 10 0.1 G 1.0 G 3.0 G 3.0 G 0.1 G 2.0 G 1.0 G Data Sheet P12653EJ2V1DS00 PC2709TB ...

Page 11

Typical S-Parameter Values (T = +25°C) A PC2709TB 5 out CC Frequency S11 MHz MAG ANG 100.0000 .227 0.2 200.0000 .239 1.0 300.0000 .245 2.9 400.0000 .244 2.5 500.0000 .243 ...

Page 12

PACKAGE DIMENSIONS 6 pin super minimold (unit: mm) +0.1 0.2 –0 12 0.7 0.65 0.65 0.9 0.1 1.3 2.0 0.2 Data Sheet P12653EJ2V1DS00 PC2709TB +0.1 0.15 – 0.1 ...

Page 13

... Observe precautions for handling because of electro-static sensitive devices. (2) Form a ground pattern as widely as possible to minimize ground impedance (to prevent undesired oscillation). All the ground pins must be connected together with wide ground pattern to decrease impedance difference. (3) The bypass capacitor should be attached to the V (4) The inductor must be attached between V accordance with desired frequency ...

Page 14

Data Sheet P12653EJ2V1DS00 PC2709TB ...

Page 15

Data Sheet P12653EJ2V1DS00 PC2709TB 15 ...

Page 16

... Specific: Aircraft, aerospace equipment, submersible repeaters, nuclear reactor control systems, life support systems or medical equipment for life support, etc. The quality grade of NEC devices is "Standard" unless otherwise specified in NEC's Data Sheets or Data Books. If customers intend to use NEC devices for applications other than those specified for Standard quality grade, they should contact an NEC sales representative in advance ...