RCH10S5R000JS06 Vishay, RCH10S5R000JS06 Datasheet - Page 3

• Manufacturer Part Number: RCH10S5R000JS06
• Description: FIXED RESISTORS SFERNICE / RCH 10 5U 5% S BA25 E3
• Manufacturer: Vishay
• Type: Thick Filmr

Specifications of RCH10S5R000JS06

• Power Rating(s): 10W
• Resistance: 5Ohm
• Tolerance (+ Or -): 5%
• Temperature Coefficient: ±150
• Mounting Style: Flange
• Construction: Chassis
• Operating Temp Range: -55C to 125C
• Case Style: Molded
• Termination Style: Radial Lug
• Military Standard: Not Required
• Failure Rate: Not Required
• Product Length (mm): 19mm
• Product Height (mm): 9mm
• Product Depth (mm): 20.6mm
• Lead Free Status / RoHS Status: Compliant

RCH
Vishay Sfernice
RECOMMENDATIONS FOR MOUNTING ONTO A HEATSINK
• Surfaces in contact must be carefully cleaned.
• The heatsink must have an acceptable flatness: From 0.05 mm to 0.1 mm/100 mm.
• Roughness of the heatsink must be around 6.3 µm. In order to improve thermal conductivity, surfaces in contact (alumina,
• The fastening of the resistor to the heatsink is under pressure control of two screws (not supplied).
• In order to improve the dissipation, either forced-air cooling or liquid cooling may be used.
• A low thermal radiation of the case allows several resistors to be mounted onto the same heatsink.
• Do not forget to respect an insulation value between two resistors (dielectric strength in dry air 1 kV/mm).
• In any case the hot spot temperature, measured locally on the case must not exceed 125 °C.
• Tests should be performed by the user.
CHOICE OF THE HEATSINK
The user must choose the heatsink according to working conditions of the component (power, room temperature). Maximum
working temperature must not exceed 125 °C. The dissipated power is simply calculated by the following ratio:
Example:
R
www.vishay.com
42
TH (c- a)
Tightening Torque
on heatsink
heatsink) are coated with a silicone grease (type Sl 340 from Rhône-Poulenc or Dow 340 from Dow Corning).
P:
ΔT:
R
R
TH (j - c)
TH (c- a)
:
: Thermal resistance value measured between resistance layer and outer side of the resistor.
: Thermal resistance value measured between outer side of the resistor and room temperature.
For RCH 25 power rating 20 W at ambient temperature + 50 °C.
ΔT ≤ 125 °C - 50 °C ≤ 75 °C
R
R
R
Expressed in W
Difference between maximum working temperature and room temperature.
It is the thermal resistance of the component (See Special Features table).
It is the thermal resistance of the heatsink depending on the heatsink itself (type, shape) and the quality of the
fastening device.
TH (j - c)
TH (j - c)
TH (c - a)
= 1.4 °C/W (Special Features)
+ R
≤ 3.75 °C/W - 1.4 °C/W ≤ 2.35 °C/W
TH (c - a)
=
Power Resistor, for Mounting onto a Heatsink
ΔT
-------
0.5 Nm
RCH 5
P
=
For technical questions, contact:
75
----- -
20
= 3.75 °C/W
P =
Thick Film Technology
---------------------------------------------------------- -
[
R
TH (j - c)
RCH 10
0.6 Nm
ΔT
+ R
TH (c - a)
[e-mail]
]
1 ( )
RCH 25
0.7 Nm
Document Number: 50006
Revision: 14-Jun-10
RCH 50
1 Nm