1571079-9 TE Connectivity, 1571079-9 Datasheet - Page 294

• Manufacturer Part Number: 1571079-9
• Description: Switch Rocker ON OFF ON SPDT Faston Rocker 16A 250VAC 372.85VA >100000Cycle
• Manufacturer: TE Connectivity

Specifications of 1571079-9

• Mounting: Panel Mount
• Switch Configuration: ON OFF ON
• Pole Throw Configuration: SPDT
• Maximum Power Rating: 372.85 VA
• Maximum Ac Voltage Rating: 250 V

Catalog 1308390
Issued 9-04
www.tycoelectronics.com
• Oil-tight: A generic term for a panel seal (see) commonly used
• Operating Force: See Actuation Force.
• Operating Temperature: The range of temperature within
• Operator: A panel mounted mechanical device (pushbutton,
• Overtravel: The distance the actuator may move between initial
• Panel Seal: A panel seal provides a defined level of protection
• Pole: The number of separate circuits that can be active through a
• Power Factor (PF): A measure of the inductive or capacitive
• Process Seal: A seal that prevents damage to or contamination of
• Push-On/Push-Off: See Push-Push.
• Push-Push (Alternative Action, Push-On/Push-Off): A
• Quick-Connect Terminals: Flat tab or blade style terminals
• Resistive load: A load in which the current and voltage are in
• Shorting Contact: See Make-Before-Break.
• Single Break Contacts: A contact mechanism using one set of
• Splashproof: See panel Seal.
• Spring Return: See Momentary.
in industrial settings. Defined by NEMA (see) and IP (see)
standards.
which the device may be used. Unit of Measure: Degrees
celsius or fahrenheit (C or F).
selector, keylock, etc.) without contacts to which one or more
contact blocks (see) may be added to make a complete switch.
contact position and the extreme mechanical position of the
actuator without damage to the switch. See travel. Pretravel.
Unit of Measure: Inch. Degree.
against penetration of liquids through which the switch and
switch-to-panel interface to the rear of a panel. Unit of
Measure: Inches/ft. of water.
switch at any one time. A single pole switch allows one closed
circuit at a time. A double pole switch allows two closed
circuits, etc.
character of an electrical load. Unit of Measure: 0 to 1 (e.g.
0.75)
the switch during the specified mechanical process. See wave
solderable. Surface Moutable.
pushbutton switch style in which the electrical state of the
switch is maintained between actuations of the plunger.
designed to accept push-on female wire connectors (instead of
soldering). The most popular sizes are: 0.250”, 0.110” wide.
phase. See Capacitive Load, Inductive Load, Power Factor,
Inrush.
contacts to make or break a given circuit. Typical of electronic
or low power switches. See Double-Break Contacts.
Dimensions are in inches
and millimeters unless otherwise
specified. Values in parentheses
or brackets are metric equivalents. to change.
Index/Matrixes
Glossary
Dimensions are shown for
reference purposes only.
Specifications subject
• Storage Temperature: The range of temperature within which
• Surface Mount Devices: Components that are compatible with
• Tactile Feel (Feedback): A mechanical signal (typically a
• Terminal: The metal portion of the switch, exterior to the body,
• Throws: Number of circuits that can be controlled by any one
• Travel: The total distance the actuator moves to change electrical
• Washable: Applied to PC board mounted devices indicating
• Wave Solderable: Indicates the device is suitable for the wave
• Wiping Contact: A contact mechanism in which the movable
the device may be stored. Typically this is a wider range than
operating temperature. Unit of Measure: Degrees celsius or
fahrenheit (C or F).
surface mount PC board technology. Holes are not used for
component mounting. Component leads are soldered to pads on
the surface of the PC boards. For switches typically defined by
surface mount terminations (e.g., J-bend, L-bend, butt, etc.) and
compatibility with surface mount soldering (e.g., vapor phase
reflow, infrared, etc.) and cleaning processes.
“snap” or “click”) that indicates contact closure to the operator.
that is used to connect the switch to an electrical circuit.
Examples: PC, wire lug, Turrett, quick-connect, wire-wrap, etc.
pole of a switch. Example: In a single pole — double throw
(SPDT) switch, only one circuit may be completed at a time.
However, there are two possible circuits (throws) that can be
made.
position. See Pretravel. Overtravel. Unit of Measure: Inches,
degrees.
compatibility with cleaning processes used after soldering. No
degredation of electrical or mechanical parameters occurs.
soldering and cleaning processes as supplied. See Process Seal.
contact with the fixed contact with a wiping motion. Typical to
slide and rotary switches.
USA: 1-800-522-6752
Canada: 1-905-470-4425
Mexico: 01-800-733-8926
C. America: 52-55-5-729-0425
South America: 55-11-3611-1514
Hong Kong: 852-2735-1628
Japan: 81-44-844-8013
UK: 44-141-810-8967
M9
M