MKT1813410405 Vishay, MKT1813410405 Datasheet - Page 8

• Manufacturer Part Number: MKT1813410405
• Description: Cap Film 0.1uF 400VDC/200VAC PET 10% 7 X 19mm AXL Bulk
• Manufacturer: Vishay
• Series: MKT1813r

Specifications of MKT1813410405

• Package/case: 7(Max) X 19(Max)
• Mounting: Through Hole
• Capacitance Value: 0.1 uF
• Voltage: 400|200 Vdc|Vac
• Dielectric: PET
• Product Length: 19(Max) mm
• Tolerance: 10 %
• Operating Temperature: -55 to 100 °C
• Voltage Rating: 400 Volts
• Capacitance: 0.1 uF
• Termination Style: Axial
• Dimensions: 7 mm Dia. x 19 mm L
• Operating Temperature Range: - 55 C to + 100 C
• Load Life: 300000 Hrs
• Product: Metallized Polyester Film Capacitors
• Capacitor Application: Safety / Suppression
• Capacitor Dielectric Type: Polyester
• Capacitance Tolerance: ± 10%
• Capacitor Case Style: Radial Leaded
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant

MKT 1813
Vishay Roederstein
POWER DISSIPATION AND MAXIMUM COMPONENT TEMPERATURE RISE
The power dissipation must be limited in order not to exceed the maximum allowed component temperature rise as a function of
the free ambient temperature.
The power dissipation can be calculated according type detail specification “HQN-384-01/101: Technical Information Film
Capacitors”.
The component temperature rise (ΔT) can be measured (see section “Measuring the component temperature” for more details)
or calculated by ΔT = P/G:
MEASURING THE COMPONENT TEMPERATURE
A thermocouple must be attached to the capacitor body as in:
The temperature is measured in unloaded (T
The temperature rise is given by ΔT = T
To avoid radiation or convection, the capacitor should be tested in a wind-free box.
APPLICATION NOTE AND LIMITING CONDITIONS
These capacitors are not suitable for mains applications as across-the-line capacitors without additional protection, as described
hereunder. These mains applications are strictly regulated in safety standards and therefore electromagnetic interference
suppression capacitors conforming the standards must be used.
To select the capacitor for a certain application, the following conditions must be checked:
1. The peak voltage (U
2. The peak-to-peak voltage (U
3. The voltage peak slope (dU/dt) shall not exceed the rated voltage pulse slope in an RC-circuit at rated voltage and without
4. The maximum component surface temperature rise must be lower than the limits (see figure max. allowed component
www.vishay.com
24
ringing. If the pulse voltage is lower than the rated DC voltage, the rated voltage pulse slope may be multiplied by U
divided by the applied voltage.
For all other pulses following equation must be fulfilled:
T is the pulse duration
The rated voltage pulse slope is valid for ambient temperatures up to 85 °C. For higher temperatures a derating factor of 3 %
per K shall be applied.
temperature rise).
2
• ΔT = Component temperature rise (°C)
• P = Power dissipation of the component (mW)
• G = Heat conductivity of the component (mW/°C)
×
T
∫
0
⎛
⎝
dU
------- -
dt
⎞
⎠
2
×
dt U
<
Rdc
P
) shall not be greater than the rated DC voltage (U
×
⎛
⎝
dU
------- -
dt
⎞
⎠
P-P
rated
) shall not be greater than 2
For technical questions, contact: [e-mail]
C
- T
amb
amb
.
) and maximum loaded condition (T
DC Film Capacitor
MKT Axial Type
√
2 x U
Rac
to avoid the ionisation inception level
Thermocouple
Rdc
)
C
).
Document Number: 26013
Revision: 08-Dec-08
Rdc
and