GNM314R71C393KD01D Murata, GNM314R71C393KD01D Datasheet - Page 6

• Manufacturer Part Number: GNM314R71C393KD01D
• Manufacturer: Murata
• Type: Ceramicr

Specifications of GNM314R71C393KD01D

• Capacitance: .039uF
• No. Of Capacitors: 4
• Tolerance (+ Or -): 10%
• Voltage: 16VDC
• Number Of Terminals: 8Terminal
• Temp Coeff (dielectric): X7R
• Operating Temp Range: -55C to 125C
• Mounting Style: Surface Mount
• Package / Case: 1206
• Construction: SMT Chip
• Failure Rate: Not Required
• Product Height (mm): 0.8mm
• Product Depth (mm): 1.6mm
• Product Length (mm): 3.2mm
• Lead Diameter (nom): Not Requiredmm
• Terminal Pitch: 0.8mm
• Lead Free Status / RoHS Status: Compliant

!Note
!Note
Table A
Note 1 : Nominal values denote the temperature coefficient within a range of 25D to 125D.
No.
16
17
18
Continued from the preceding page.
Humidity
Steady
State
Humidity
Load
High
Temperature
Load
Char.
• Please read rating and !CAUTION (for storage, operating, rating, soldering, mounting and handling) in this catalog to prevent smoking and/or burning, etc.
• This catalog has only typical specifications because there is no space for detailed specifications. Therefore, please approve our product specifications or transact the approval sheet for product specifications before ordering.
Please read rating and !CAUTION (for storage, operating, rating, soldering, mounting and handling) in this PDF catalog to prevent smoking and/or burning, etc.
This catalog has only typical specifications. Therefore, you are requested to approve our product specifications or to transact the approval sheet for product specificaions before ordering.
5C
Item
Appearance
Capacitance
Change
Q/D.F.
I.R.
Dielectric
Strength
Appearance
Capacitance
Change
Q/D.F.
I.R.
Dielectric
Strength
Appearance
Capacitance
Change
Q/D.F.
I.R.
Dielectric
Strength
Nominal Values
(ppm/D) Note 1
The measured and observed characteristics should satisfy the
specifications in the following table.
No marking defects
Within T5% or T0.5pF
(Whichever is larger)
30pF and over : QU350
10pF and over, 30pF and
below :
10pF and below :
C : Nominal Capacitance
More than 1,000MΩ or 50Ω • F (Whichever is smaller)
No failure
The measured and observed characteristics should satisfy the
specifications in the following table.
No marking defects
Within T7.5% or T0.75pF
(Whichever is larger)
30pF and over : QU200
30pF and below :
C : Nominal Capacitance
More than 500MΩ or 25Ω • F (Whichever is smaller)
No failure
The measured and observed characteristics should satisfy the
specifications in the following table.
No marking defects
Within T3% or T0.3pF
(Whichever is larger)
30pF and over : QU350
10pF and over, 30pF and
below :
10pF and below :
More than 1,000MΩ or 50Ω • F (Whichever is smaller)
No failure
C : Nominal Capacitance
Compensating Type
(pF)
(pF)
(pF)
0T30
Temperature
QU275+5C/2
QU200+10C
QU100+10C/3
QU275+5C/2
QU200+10C
Specifications
Char.
Char.
Char.
R7 : Within T12.5%
F5 : Within T30%
R7 : Within T12.5%
F5 : Within T30%
R7 : Within T12.5%
F5 : Within T30%
R7
R7
R7
F5
F5
F5
Max.
0.58
0.025 max.
0.025 max.
0.025 max.
25V min.
0.05 max.
25V min.
0.05 max.
25V min.
0.05 max.
High Dielectric Type
Y55
0.035 max.
0.035 max.
0.035 max.
0.07 max.
0.07 max.
0.07 max.
16V
16V
16V
Y0.24
Min.
0.035 max.
0.035 max.
0.035 max.
10V
10V
10V
Y
Y
Y
Capacitance Change from 25D (%)
Let the capacitor sit at 40T2D and 90 to 95% humidity for
500T12 hours.
Remove and let sit for 24T2 hours (temperature compensating
type) or 48T4 hours (high dielectric constant type) at room tem-
perature, then measure.
Apply the rated voltage at 40T2D and 90 to 95% humidity for
500T12 hours. Remove and let sit for 24T2 hours (temperature
compensating type) or 48T4 hours (high dielectric constant
type) at room temperature, then measure. The charge/dis-
charge current is less than 50mA.
Apply 200% of the rated voltage for 1000T12 hours at the
maximum operating temperature T3D. Let sit for 24T2 hours
(temperature compensating type) or 48T4 hours (high dielectric
constant type) at room temperature, then measure.
The charge/discharge current is less than 50mA.
#Initial measurement for high dielectric constant type.
Apply 200% of the rated DC voltage for one hour at the maxi-
mum operating temperature T3D. Remove and let sit for 48T4
hours at room temperature. Perform initial measurement.
Specifications and Test Methods
Max.
0.40
Y30
Y0.17
Min.
Test Method
Max.
0.25
C02E10.pdf 04.1.20
Y10
Y0.11
Min.
47
8