MIC2042-2YTS Micrel Inc, MIC2042-2YTS Datasheet - Page 3

• Manufacturer Part Number: MIC2042-2YTS
• Description: 41 Mohm Low Voltage Switch -
• Manufacturer: Micrel Inc
• Type: High Side Switchr

Specifications of MIC2042-2YTS

• Lead Free Status: Lead free
• Number Of Outputs: 1
• Rds (on): 60 mOhm
• Internal Switch(s): Yes
• Current Limit: Adjustable
• Voltage - Input: 0.8 ~ 5.5 V
• Operating Temperature: -40°C ~ 85°C
• Mounting Type: Surface Mount
• Package / Case: 14-TSSOP
• Other names: 576-1698-5; MIC2042-2YTS

January 2005
MIC2042/2043
Pin Description
Pin Number
8-Pin SOP
N/A
N/A
N/A
N/A
N/A
5,7
6,8
1
2
3
4
14-Pin TSSOP
Pin Number
10,11,14
8,12
13
2
3
5
9
6
7
1
4
Pin Name
PWRGD
UVLOIN
/FAULT
PGREF
SLEW
VBIAS
VOUT
GND
ILIM
VIN
EN
Pin Function
Switch Enable Input: Gate control pin of the output MOSFET available as an
active high (–1) or active low (–2) input signal.
Fault Status Output: Open-drain N-Channel device, active low. This pin
indicates an overcurrent or thermal shutdown condition. For an overcurrent
event, /FAULT is asserted if the duration of the overcurrent condition lasts
longer than 28ms.
Ground Connection: Tie to analog ground.
Slew-Rate Control Input: A capacitor connected between this pin and ground
will reduce (slow) the output slew-rate. The output turn-on time must be less
than the nominal flag delay of 28ms in order to avoid nuisance tripping of the
/FAULT output since V
at the input) before the /FAULT signal delay elapses. The capacitor requires a
16V rating, or greater, 25V is recommended. See “Applications Information,”
“Output Slew-Rate Adjustment” for further detail.
Current Limit Set: A resistor, R
limit threshold as CLF/R
the “Electrical Characteristics” table. For the MIC2042/43, the continuous
output current range is 0.5A to 3A.
Switch Input Supply: The drain of the output MOSFET. The range of input for
the switch is 0.8V to 5.5V. These pins must be externally connected together
to achieve rated performance.
Switch Output: The source of the output MOSFET. These pins must be
externally connected together to achieve rated performance.
Bias Supply Input: This input pin supplies power to operate the switch and
internal circuitry. The input range for V
voltage (V
connect VBIAS to VIN externally.
Power-Good Threshold (Input): Analog reference used to specify the
PWRGD threshold. When the voltage at this pin exceeds its threshold, V
PWRGD is asserted high. An external resistive divider network is used to
determine the output voltage level at which V
“Functional Description” for further detail. When the PWRGD signal is not
utilized, this input should be tied to VOUT.
Power-Good Output: Active high, open-drain. This pin asserts high when the
voltage at PGREF exceeds its threshold.
Undervoltage Lockout Adjust Input: With this pin left open, the UVLO
threshold is internally set to 1.45V. When the switching voltage (V
1.6V, connecting an external resistive divider to this input will lower the
UVLO threshold. The total resistance of the divider must be less than
200kΩ. See “Applications Information” for further detail.
IN
3
) is between 1.6V to 5.5V and the use of a single supply is desired,
OUT
SET
must be “fully on” (i.e., within 200mV of the voltage
, where CLF is the current limit factor specified in
SET
, connected to this pin sets the current
BIAS
is 1.6V to 5.5V. When switched
TH
is exceeded. See
IN
M0512-112603
) is below
TH
Micrel
,