LTC1060CSW#TRM Linear Technology, LTC1060CSW#TRM Datasheet
LTC1060CSW#TRM
Specifications of LTC1060CSW#TRM
Available stocks
Related parts for LTC1060CSW#TRM
LTC1060CSW#TRM Summary of contents
Page 1
... Technology’s enhanced LTCMOS™ silicon gate process. Because of this, low offsets, high dynamic range, high center frequency Q product and excellent temperature stability are obtained. The LTC1060 is pinout compatible with MF10. , LTC and LT are registered trademarks of Linear Technology Corporation. LTCMOS trademark of Linear Technology Corporation. OUTPUT 20 100k ...
Page 2
LTC1060 ABSOLUTE AXI U RATI GS (Note 1) Supply Voltage ........................................................ 18V Power Dissipation .............................................. 500mW Operating Temperature Range LTC1060AC/LTC1060C ................ – 40°C ≤ T LTC1060AM/LTC1060M ............ – 55°C ≤ T Storage Temperature Range ................. – 65°C ...
Page 3
ELECTRICAL CHARACTERISTICS range, otherwise specifications are at T PARAMETER CONDITIONS Center Frequency Range f • Q ≤ 100kHz 0 Clock-to-Center Frequency Ratio LTC1060A Mode 1, 50:1, f LTC1060 Mode 1, 50:1, f LTC1060A Mode 1, 100:1, f LTC1060 Mode 1, ...
Page 4
LTC1060 W U TYPICAL PERFOR A CE CHARACTERISTICS Graph 1. Mode Deviation vs Q CLK ± 25° 250kHz CLK 0 –0.4 –0.8 f CLK –1.2 = ...
Page 5
W U TYPICAL PERFOR A CE CHARACTERISTICS Graph 10. Mode and Q CLK 0 CLK 1 ±2. 25° 0.8 CLK = 100 0.6 0.4 Q ...
Page 6
LTC1060 W U TYPICAL PERFOR A CE CHARACTERISTICS Graph 19. Mode 3 ( and Q CLK 0 CLK 0 ± 25°C A 0.6 f CLK = 100:1 ...
Page 7
PIN DESCRIPTION AND APPLICATIONS INFORMATIO Power Supplies + + The V and V (pins 7 and 8) and the (Pins 14 and 13) are, respectively, the analog and digital positive and negative supply pins. ...
Page 8
LTC1060 U U APPLICATIO S I FOR ATIO internal op amps, as well as the reference point of all the internal switches are connected to the AGND pin. Because of this, a “clean” ground is recommended Ratio CLK ...
Page 9
U U APPLICATIO S I FOR ATIO Table 2. Wideband RMS Noise f CLK 50:1 ±5V 100:1 ±5V 50:1 ±2.5V 100:1 ±2.5V 50:1 ±5V 100:1 ±5V 50:1 ±2.5V ±2.5V 100.1 50:1 ±5V 100:1 ±5V ±2.5V 50:1 ...
Page 10
LTC1060 U U DEFINITION OF FILTER FUNCTIONS 3. Highpass function: available only in mode 3 at the ouput Pins 3 (18). (Figure 3 G( OHP s(ω /Q) + ω gain ...
Page 11
W ODES OF OPERATIO Table 4. Modes of Operation: 2nd Order Functions MODE PIN 1 (20) PIN 2 (19 ...
Page 12
LTC1060 W ODES OF OPERATIO S1A 3 5 (16 – 4 – (17) – A/B 1/2 LTC1060 6 15 – CLK ...
Page 13
W ODES OF OPERATIO S1A 3 5 (18) (16 – – + (17) – A/B 1/2 LTC1060 6 15 – CLK CLK f ...
Page 14
LTC1060 W ODES OF OPERATIO R3 R2 AP2 S1A 3 5 (18) (16 – – + (17) – A/B 1/2 LTC1060 CLK ...
Page 15
W ODES OF OPERATIO LP1 S1A 3 5 (18) (16) – 4 – + (17) – A/B 1/2 LTC1060 CLK – ...
Page 16
LTC1060 COMM THE Modes 2, 2a, and 2b have a notch output which frequency can be tuned independently from the center frequency For all cases, however, f <f ...
Page 17
COMM THE mode 2b section (Figure 22), has a gain exceeding unity which limits the dynamic range of the overall filter. For very selective bandpass/bandreject filters, the mode 3a R41 R31 R21 R11 ...
Page 18
LTC1060 COMM THE LTC1060 R41 R31 R21 R11 ...
Page 19
... MOLD FLASH OR PROTRUSIONS SHALL NOT EXCEED .010 INCH (0.254mm) Information furnished by Linear Technology Corporation is believed to be accurate and reliable. However, no responsibility is assumed for its use. Linear Technology Corporation makes no represen- tation that the interconnection of its circuits as described herein will not infringe on existing patent rights. ...
Page 20
... J20 0801 .496 – .512 NOTE .394 – .419 (10.007 – 10.643) N .037 – .045 (0.940 – 1.143) .004 – .012 (0.102 – 0.305) S20 (WIDE) 0502 LW/TP 1202 1K REV B • PRINTED IN USA LINEAR TECHNOLOGY CORPORATION 1988 1060fb ...