SLFDM44H-064JI STEC, SLFDM44H-064JI Datasheet

SLFDM44H-064JI

Manufacturer Part Number

SLFDM44H-064JI

Description

Manufacturer

STEC

Type

Flash Diskr

Datasheet

1.SLFDM44H-064JI.pdf (23 pages)

Specifications of SLFDM44H-064JI

Density

64MByte

Operating Supply Voltage (typ)

3.3/5V

Operating Temperature (min)

-40C

Operating Temperature (max)

85C

Package Type

Not Required

Mounting

Surface Mount

Pin Count

Operating Temperature Classification

Industrial

Operating Supply Voltage (min)

3.18/4.75V

Operating Supply Voltage (max)

3.465/5.25V

Programmable

Yes

Lead Free Status / RoHS Status

Not Compliant

Current page: 1 of 23
Download datasheet (335Kb)

Web:

64MB Solid-State Flash Disk Module

FEATURES

• Compact Form Factor designed to plug into standard IDE

• Standard IDE Interface

• Configures as Master or Slave IDE device

• Endurance Guarantee of 2,000,000 Write/Erase Cycles

• Standard 5V Power Supply

• Replaces IDE hard drive for applications where tough

• Solid-State (no moving parts)

• High Shock and Vibration Limits

• 512 Byte Sector and ECC Defect Management

• No “Spin” Noise Compared to Traditional Rotating

• Standard ECC Engine

• 7 Year Warranty

• Other Features Available

Vertical Plug-in

and Housing

40-Pin with

connector

- 44-pin connector and 40-pin connector available

- Vertical and horizontal plug-in available

- Housing optional for vertical plug-in

(also supports a 3.3V power supply)

environments prohibit use of traditional rotating media

Compatible to IDE Hard Disk Drives

Media

- Power Down Protection. A built-in feature that protects

- Endurance Status Monitor. A firmware option that

- Password Protection/Write Protection. A custom utility

the module from losing data during a write operation

when a lost of power or an unexpected removal from

the host system occurred.

allows applications to estimate the remaining life

span of the device.

software that allows the administrator and user to

set passwords for up to four partitions.

Horizontal

www.simpletech.com

Plug-In

(inquire for more information)

Vertical Plug-in

Vertical

Plug-In

and Housing

44-Pin with

Document Part Number 61000-02832-314 July 2005

GENERAL DESCRIPTION

This SimpleTech product is a solid-state Flash Disk Module

with a standard IDE interface, common on IDE hard drives.

The module plugs directly into either a 40-pin connector

and 4-pin power connector, or a 44 pin connector without

need for a cable. This eliminates the installation confusion,

the cost, and the potential failures commonly associated

with interface cables..

SimpleTech OEM flash disk modules are the product of

choice in applications requiring high reliability and high

tolerance to shock, vibration, humidity, altitude, and

temperature. Because there are no moving parts to

service or maintain, flash disk modules are reliable

alternatives to mechanical hard disk drives for high

availability and mission critical applications.

While the inherent ruggedness and reliability of solid state

storage relative to rotating hard drives is intuitive, new

applications for OEM flash disk modules are emerging due

to the low cost per usable megabyte. Most applications

using embedded operating systems such as VxWorks™,

Windows XP/embedded™, and Linux™ don’t have multi-

gigabyte data storage requirements, and therefore a cost

savings can be realized when using this robust media.

ORDERING INFORMATION

SimpleTech Part No.

SLFDM40LPV-064J ............... 40-Pin ............................... Vertical

SLFDM40LPH-064J ............... 40-Pin .......................... Horizontal

SLFDM40LPVS-064J ............ 40-Pin .............. Vertical/Housing

SLFDM44V-064J .................... 44-Pin ............................... Vertical

SLFDM44H-064J ................... 44-Pin .......................... Horizontal

SLFDM44LPVS-064J ............ 44-Pin ............. Vertical /Housing

Option Designators

Options can be selected by using the Option Designators

in the part number in the following format:

SLFDMpqr-064J(U)(I)

where p=# of pins, q=LP if low profile, r=plug-in /housing

U RoHS compliant lead free product

Commercial Operating Temperature range: 0 to 70°C

(designator is BLANK)

Industrial Operating Temperature range: -40 to 85°C

(designator=I)

(where p=connector; q=LP if low profile; r=plug-in and housing;

SimpleTech P/N:

U=RoHS compliant lead-free; I=Ind. Op. Temp;)

# of Pins

Plug-In/Housing

Page 1

Related parts for SLFDM44H-064JI

SLFDM44H-064JI Summary of contents

Page 1

... ORDERING INFORMATION SimpleTech Part No. SLFDM40LPV-064J ............... 40-Pin ............................... Vertical SLFDM40LPH-064J ............... 40-Pin .......................... Horizontal SLFDM40LPVS-064J ............ 40-Pin .............. Vertical/Housing SLFDM44V-064J .................... 44-Pin ............................... Vertical SLFDM44H-064J ................... 44-Pin .......................... Horizontal SLFDM44LPVS-064J ............ 44-Pin ............. Vertical /Housing Option Designators Options can be selected by using the Option Designators in the part number in the following format: SLFDMpqr-064J(U)(I) where p=# of pins, q=LP if low profile, r=plug-in /housing ...

Page 2

SLFDMpqr-064J(U)(I) SimpleTech P/N: (where p=connector; q=LP if low profile; r=plug-in and housing; U=RoHS compliant lead-free; I=Ind. Op. Temp) DIMENSIONS AND JUMPERS Units are in inches. Tolerances are ±0.005. SLFDM40LPV-064J(U)(I) Location of Pin 1 (Top View of Connector) 0.125 0.140 SLFDM40LPH-064J(U)(I) ...

Page 3

... U=RoHS compliant lead-free; I=Ind. Op. Temp) DIMENSIONS AND JUMPERS Units are in inches. Tolerances are ±0.005. SLFDM44V-064J(U)(I) Location of Pin 1 (Top View of Connector) 0.175 0.105 SLFDM44H-064J(U)(I) 0.072 D Location of Pin 1 0.175 0.075 (continued) 44-Pin IDE Connector 0.072 D 2.000 ...

Page 4

SLFDMpqr-064J(U)(I) SimpleTech P/N: (where p=connector; q=LP if low profile; r=plug-in and housing; U=RoHS compliant lead-free; I=Ind. Op. Temp) DIMENSIONS AND JUMPERS Units are in inches. Tolerances are ±0.005. SLFDM40LPVS-064J(U)(I) Master/Slave Jumper Install Jumper as shown for slave mode. NoJumper as ...

Page 5

SLFDMpqr-064J(U)(I) SimpleTech P/N: (where p=connector; q=LP if low profile; r=plug-in and housing; U=RoHS compliant lead-free; I=Ind. Op. Temp) PIN CONFIGURATION Pinout Pin Pin Pin Num Symbol Num 1 -RESET 23 2 GND 24 3 D07 25 4 D08 26 5 ...

Page 6

SLFDMpqr-064J(U)(I) SimpleTech P/N: (where p=connector; q=LP if low profile; r=plug-in and housing; U=RoHS compliant lead-free; I=Ind. Op. Temp) Signal Description Signal Name Dir -DASP D15-D00 18, 16, 14, 12, 10 ...

Page 7

SLFDMpqr-064J(U)(I) SimpleTech P/N: (where p=connector; q=LP if low profile; r=plug-in and housing; U=RoHS compliant lead-free; I=Ind. Op. Temp) ABSOLUTE MAXIMUM RATINGS Parameter Voltage on any pin w.r.t. Vss Storage Temperature range RECOMMENDED OPERATING CONDITIONS Parameter Commercial operating temperature Industrial operating ...

Page 8

SLFDMpqr-064J(U)(I) SimpleTech P/N: (where p=connector; q=LP if low profile; r=plug-in and housing; U=RoHS compliant lead-free; I=Ind. Op. Temp) ENVIRONMENTAL CHARACTERISTICS Leaded Cards (without the “U” option) Shock half-sine, 0.330 ms to 0.750 ms (per MIL-STD-202G Method 213B, Condition ...

Page 9

SLFDMpqr-064J(U)(I) SimpleTech P/N: (where p=connector; q=LP if low profile; r=plug-in and housing; U=RoHS compliant lead-free; I=Ind. Op. Temp) AC CHARACTERISTICS (Ta = 0°C to 70°C for commercial temperature parts –40°C to 85°C for industrial temperature parts; VCC = ...

Page 10

SLFDMpqr-064J(U)(I) SimpleTech P/N: (where p=connector; q=LP if low profile; r=plug-in and housing; U=RoHS compliant lead-free; I=Ind. Op. Temp) AC CHARACTERISTICS True IDE Mode Access Read/Write Timings ADDR valid -IORD/-IOWR D15 to D0 (Write) D15 to D0 (Read) -IOIS16 IORDY (continued) ...

Page 11

SLFDMpqr-064J(U)(I) SimpleTech P/N: (where p=connector; q=LP if low profile; r=plug-in and housing; U=RoHS compliant lead-free; I=Ind. Op. Temp) TRUE IDE MODE The drive is configured in a True IDE mode at power up. The data register is accessed in word ...

Page 12

SLFDMpqr-064J(U)(I) SimpleTech P/N: (where p=connector; q=LP if low profile; r=plug-in and housing; U=RoHS compliant lead-free; I=Ind. Op. Temp) TASK FILE REGISTER SPECIFICATION These registers are used for reading and writing data to the drive. True IDE Mode I/O Map -CE2 ...

Page 13

SLFDMpqr-064J(U)(I) SimpleTech P/N: (where p=connector; q=LP if low profile; r=plug-in and housing; U=RoHS compliant lead-free; I=Ind. Op. Temp) Data Register The Data Register bit read/write register used for transferring data between the drive and the host. This ...

Page 14

SLFDMpqr-064J(U)(I) SimpleTech P/N: (where p=connector; q=LP if low profile; r=plug-in and housing; U=RoHS compliant lead-free; I=Ind. Op. Temp) Sector Count Register This register contains the numbers of sectors of data requested to be transferred on a read or write operation ...

Page 15

SLFDMpqr-064J(U)(I) SimpleTech P/N: (where p=connector; q=LP if low profile; r=plug-in and housing; U=RoHS compliant lead-free; I=Ind. Op. Temp) Drive/Head Register This register select the device address translation (CHS or LBA) and provides head address (CHS) or high order address bits ...

Page 16

SLFDMpqr-064J(U)(I) SimpleTech P/N: (where p=connector; q=LP if low profile; r=plug-in and housing; U=RoHS compliant lead-free; I=Ind. Op. Temp) Status Register This read only register indicates status of a command execution. When the BSY bit is “0”, the other bits are ...

Page 17

SLFDMpqr-064J(U)(I) SimpleTech P/N: (where p=connector; q=LP if low profile; r=plug-in and housing; U=RoHS compliant lead-free; I=Ind. Op. Temp) Device Control Register This write only register is used for controlling the interrupt request and issuing an ATA soft reset to the ...

Page 18

SLFDMpqr-064J(U)(I) SimpleTech P/N: (where p=connector; q=LP if low profile; r=plug-in and housing; U=RoHS compliant lead-free; I=Ind. Op. Temp) ATA COMMAND SPECIFICATIONS This table with the following paragraphs summarizes the ATA command set. No. Command set 1 Check Power Mode 2 ...

Page 19

SLFDMpqr-064J(U)(I) SimpleTech P/N: (where p=connector; q=LP if low profile; r=plug-in and housing; U=RoHS compliant lead-free; I=Ind. Op. Temp) Check Power Mode (code: E5h or 98h) This command checks the power mode. Execute Drive Diagnostic (code: 90h) This command performs the ...

Page 20

SLFDMpqr-064J(U)(I) SimpleTech P/N: (where p=connector; q=LP if low profile; r=plug-in and housing; U=RoHS compliant lead-free; I=Ind. Op. Temp) Word Data Total Address Bytes 0 044AH 2 General configuration bit-significant information 1 XXXXH 2 Default number of cylinders 2 0000H 2 ...

Page 21

SLFDMpqr-064J(U)(I) SimpleTech P/N: (where p=connector; q=LP if low profile; r=plug-in and housing; U=RoHS compliant lead-free; I=Ind. Op. Temp) Request Sense (code: 03h) This command requests an extended error code after a command ends with an error. Refer to table below. ...

Page 22

SLFDMpqr-064J(U)(I) SimpleTech P/N: (where p=connector; q=LP if low profile; r=plug-in and housing; U=RoHS compliant lead-free; I=Ind. Op. Temp) Write Multiple (code: C5h) This command is similar to the Write Sectors command. Interrupts are not presented on each sector, but on ...

Page 23

... P/N SLFDM44LPH-064J(I) corrected to SLFDM44H-064J(I). SimpleTech Inc. reserves the right to make changes to specifications and product descriptions such as but not limited to numbers, parameters and other technical information contained herein without notice. Contact SimpleTech Inc. sales office to obtain the latest specifications. ...

Related keywords

SLFDM44H-064JI datasheet
SLFDM44H-064JI data sheet
SLFDM44H-064JI pdf datasheet
SLFDM44H-064JI component
SLFDM44H-064JI part
SLFDM44H-064JI distributor
SLFDM44H-064JI RoHS
SLFDM44H-064JI datasheet download