LEDWCD050S035ST Autec Power Systems, LEDWCD050S035ST Datasheet - Page 3

• Manufacturer Part Number: LEDWCD050S035ST
• Manufacturer: Autec Power Systems

Specifications of LEDWCD050S035ST

• Lead Free Status / RoHS Status: Supplier Unconfirmed

Efficiency @ Full Load and 115VAC (min)
Efficiency @ Full Load and 115VAC (typ)
Efficiency @ Full Load and 230VAC (min)
Efficiency @ Full Load and 230VAC (typ)
NOTES:
NOTES:
1. Measured at full load, 220VAC input.
1. Measured at full load, 220VAC input.
2. Ripple & noise are measured at 20MHz of bandwidth oscilloscope and the output paralleled a 0.1uf ceramic capacitor &
2. Ripple & noise are measured at 20MHz of bandwidth oscilloscope and the output paralleled a 0.1uf ceramic capacitor &
3. For 4200mA output model, measured at 110VAC input, 80%load and 25
3. For 4200mA output model, measured at 110VAC input, 80%load and 25
4. For 4200mA output model, measured at 110VAC input, 80%load and 45
4. For 4200mA output model, measured at 110VAC input, 80%load and 45
5. All parameters NOT specially mentioned are measured at 220VAC input, rated load and 25
5. All parameters NOT specially mentioned are measured at 220VAC input, rated load and 25
6. A suffix -XXXX may be added to denote variation or modifications to the base product, were X can be any alphanumeric
6. A suffix -XXXX may be added to denote variation or modifications to the base product, were X can be any alphanumeric
7. Class 2 output (USR & CNR).
7. Class 2 output (USR & CNR).
8. Class 2 output (USR), Non-Class 2 output (CNR).
8. Class 2 output (USR), Non-Class 2 output (CNR).
9. None Class 2 output (USR & CNR).
9. None Class 2 output (USR & CNR).
10. Specifications are subject to change without notice. AUTEC can't be held liable for errors or omissions or the consequences thereof.
10. Specifications are subject to change without notice. AUTEC can't be held liable for errors or omissions or the consequences thereof.
10 uf electrolytic capacitor.
10 uf electrolytic capacitor.
Efficiency
Efficiency
character or blank
character or blank
Notes:
For the driver to operate properly, the load voltage must be maintained above the minimum voltage threshold (approx. 33% of the max. output voltage for any given
model).
If the Dimming voltage is varied from 10V down to 0V, the output current can be varied from 100%Io down to 10%~20%Io.
10V output source current
Absolute maximum voltage on the 0~10V
input pin
Source current on 0~10V input pin
10V output voltage
The dimmer control may be operated from either a potentiometer or from an input signal of 0 – 10 Vdc. Two recommended implementations are
The dimmer control may be operated from either a potentiometer or from an input signal of 0 – 10 Vdc. Two recommended implementations are
provided below.
provided below.
Dimming Control (On secondary side)
Dimming Control (On secondary side)
Autec Power Systems
Autec Power Systems
667 E Cochran St, Simi Valley, CA93065
667 E Cochran St, Simi Valley, CA93065
Model
LEDWCD050SXXXYT
Parameter
LEDWCD050SXXXYT
050S420ST
Implementation 1: Potentiometer control
LEDWC( )
-10 mA
79.0%
80.0%
82.0%
83.0%
Min.
0 mA
9.8V
-2V
Implementation 2: DC input
050S333ST
LEDWC( )
80.0%
81.0%
83.0%
84.0%
Typ.
10V
-
-
-
050S280ST
LEDWC( )
81.0%
82.0%
83.0%
84.0%
10.2V
2 mA
1 mA
Max.
15V
of ambient temperature.
of ambient temperature.
of ambient temperature.
of ambient temperature.
050S210ST
LEDWC( )
83.0%
84.0%
85.0%
86.0%
www.autec.com
www.autec.com
050S175ST
of ambient temperature.
of ambient temperature.
LEDWC( )
84.0%
85.0%
86.0%
87.0%
050S140ST
LEDWC( )
85.0%
86.0%
86.0%
87.0%
050S110ST
LEDWC( )
85.0%
86.0%
86.0%
87.0%
050S070ST
LEDWC( )
85.0%
86.0%
86.0%
87.0%
050S045ST
LEDWC( )
Tel:
Tel:
86.0%
87.0%
87.0%
88.0%
Fax: [phone]
Fax: [phone]
[phone]
[phone]
6/14/2010
050S035ST
LEDWC( )
87.0%
88.0%
88.0%
89.0%