AT94K10AL-25DQC Atmel, AT94K10AL-25DQC Datasheet - Page 59

• Manufacturer Part Number: AT94K10AL-25DQC
• Manufacturer: Atmel

Specifications of AT94K10AL-25DQC

• Device System Gates: 10000
• Propagation Delay Time: 12.7ns
• Operating Supply Voltage (typ): 3.3V
• Operating Supply Voltage (max): 3.6V
• Operating Supply Voltage (min): 3V
• Operating Temperature Classification: Commercial
• Operating Temperature (min): 0C
• Operating Temperature (max): 70C
• Mounting: Surface Mount
• Pin Count: 208
• Package Type: PQFP
• Lead Free Status / RoHS Status: Not Compliant

4.15
1138I–FPSLI–1/08
FPGA I/O Interrupt Control by AVR
This is an alternate memory space for the FPGA I/O Select addresses. If the FIADR bit in the
FISCR register is set to logic 1, the four I/O addresses, FISUA - FISUD, are mapped to physical
registers and provide memory space for FPGA interrupt masking and interrupt flag status. If the
FIADR bit in the FISCR register is cleared to a logic 0, the I/O register addresses will be
decoded into FPGA select lines.
All FPGA interrupt lines into the AVR are negative edge triggered. See
priority.
Interrupt Control Registers – FISUA..D
• Bits 7..4 - FIF3 - 0: FPGA Interrupt Flags 3 - 0
The 16 FPGA interrupt flag bits all work the same. Each is set (one) by a valid negative edge
transition on its associated interrupt line from the FPGA. Valid transitions are defined as any
change in state preceded by at least two cycles of the old state and succeeded by at least two
cycles of the new state. Therefore, it is required that interrupt lines transition from 1 to 0 at
least two cycles after the line is stable High; the line must then remain stable Low for at
least two cycles following the transition. Each bit is cleared by the hardware when executing
the corresponding interrupt handling vector. Alternatively, each bit will be cleared by writing a
logic 1 to it. When the I-bit in the Status Register, the corresponding FPGA interrupt mask bit
and the given FPGA interrupt flag bit are set (one), the associated interrupt is executed.
• Bits 7..4 - FIF7 - 4: FPGA Interrupt Flags 7 - 4
See Bits 7..4 - FIF3 - 0: FPGA Interrupt Flags 3 - 0.
• Bits 7..4 - FIF11 - 8: FPGA Interrupt Flags 11 - 8
See Bits 7..4 - FIF3 - 0: FPGA Interrupt Flags 3 - 0. Not available on the AT94K05.
• Bits 7..4 - FIF15 - 12: FPGA Interrupt Flags 15 - 12
See Bits 7..4 - FIF3 - 0: FPGA Interrupt Flags 3 - 0. Not available on the AT94K05.
• Bits 3..0 - FINT3 - 0: FPGA Interrupt Masks 3 - 0
The 16 FPGA interrupt mask bits all work the same. When a mask bit is set (one) and the I-bit in
the Status Register is set (one), the given FPGA interrupt is enabled. The corresponding inter-
rupt handling vector is executed when the given FPGA interrupt flag bit is set (one) by a negative
edge transition on the associated interrupt line from the FPGA.
Note:
• Bits 3..0 - FINT7 - 4: FPGA Interrupt Masks 7 - 4
See Bits 3..0 - FINT3 - 0: FPGA Interrupt Masks 3 - 0.
Bit
$14 ($34)
$15 ($35)
$16 ($36)
$17 ($37)
Read/Write
Initial Value
1. FPGA interrupts 3 - 0 will cause a wake-up from the AVR Sleep modes. These interrupts are
treated as low-level triggered in the Power-down and Power-save modes, see
on page
7
FIF3
FIF7
FIF11
FIF15
R/W
0
69.
6
FIF2
FIF6
FIF10
FIF14
R/W
0
5
FIF1
FIF5
FIF9
FIF13
R/W
0
4
FIF0
FIF4
FIF8
FIF12
R/W
0
AT94KAL Series FPSLIC
3
FINT3
FINT7
FINT11
FINT15
R/W
0
(1)
2
FINT2
FINT6
FINT10
FINT14
R/W
0
1
FINT1
FINT5
FINT9
FINT13
R/W
0
page 60
0
FINT0
FINT4
FINT8
FINT12
R/W
0
“Sleep Modes”
for interrupt
FISUA
FSUB
FISUC
FISUD
59