HIH-5031-001S Honeywell, HIH-5031-001S Datasheet

HIH-5031-001S

Manufacturer Part Number

HIH-5031-001S

Description

Board Mount Humidity Sensors HyCal Sensing Produc 3600 Series CMOS Sen

Manufacturer

Honeywell

Datasheets

1.HIH-5031-001S.pdf (8 pages)

2.HIH-5030-001S.pdf (4 pages)

Specifications of HIH-5031-001S

Rh Range

0 % to 100 %

Rh Accuracy

+/- 3 %

Output Type

Analog

Supply Voltage (max)

5.5 V

Supply Voltage (min)

2.7 V

Supply Current

200 uA

Maximum Operating Temperature

+ 85 C

Minimum Operating Temperature

- 40 C

Mounting Style

SMD/SMT

Body Style

Rectangular

Current, Switching

500 μA

Function

Humidity

Mounting Type

Surface Mount

Primary Type

Humidity

Range, Measurement

0 to 100 % RH

Voltage, Supply

2.7 to 5.5 VDC

Lead Free Status / RoHS Status

Supplier Unconfirmed

Current page: 1 of 4
Download datasheet (147Kb)

Installation Instructions for the

HIH-5030/5031 Series Humidity Sensors

SOLDERING AND ASSEMBLY

Sensing and Control

PERSONAL INJURY

• DO NOT USE these products as safety or emergency

• The sensor’s housing does not provide electrical safety

Failure to comply with these instructions could result in

death or serious injury.

CAUTION

IMPROPER HANDLING

• Do not remove the sensor from its original protective

• Do not touch the sensor surface. Use latex finger cots.

• Do not allow objects to enter the cavity of the sensor

Failure to comply with these instructions may result in

product damage.

NOTICE

• For HIH-5030 only: Under condensing conditions where

• Shade the sensor from direct light. Intense direct light

• At the end of its working life, dispose the sensor in

CAUTION

IMPROPER CLEANING

• Insert and solder the sensor after the PCB cleaning

Failure to comply with these instructions may result in

product damage.

process.

enough liquid water forms on the sensor to create a

parasitic leakage path, the HIH-5030 Humidity Sensor

produces an erroneous reading of 0% humidity. If this

erroneous reading is assumed to be correct by your

control function, excess humidity is likely to be introduced

into the system. Once the liquid water evaporates from

the sensor and the environment returns to a non-

condensing state, the device returns to normal

functionality.

can flood junctions in the CMOS (Complementary Metal

Oxide Semiconductor) device and drive the output signal

to the minimum. This does not harm the sensor or affect

calibration. Proper operation resumes shortly after the

direct light is removed. Ambient scattered light normally

does not affect performance.

accordance with Directive 2002/96/EC (WEEE).

stop devices or in any other application where failure of

the product could result in personal injury.

isolation. Mount the sensor in a location where it cannot

be touched, or where a surrounding barrier prevents

human contact.

packaging until it is ready to be installed.

Handle the sensor by its package edges or leads.

element.

WARNING

PROTECTIVE TAPE REMOVAL

Figure 1. Protective Tape Removal

SOLDERING

Hand soldering is acceptable. If reflow soldering is required,

use a no-clean flux. Limit the contact of the flux to the leads

only. Reflow soldering profile is specified by J-STD-020B for a

small package with a peak temperature of 250

MOISTURE SEALING THE LEADS

If, in the presence of intermittent moisture or other

contaminants, there is the possibility of galvanic paths between

the leads, moisture seal the leads and exposed pads.

CAUTION

IMPROPER SENSOR POSITIONING

• Position the sensor so that its face is exposed to the

Failure to comply with these instructions may result in

product damage.

CAUTION

IMPROPER SOLDERING

• For better product reliability, the HIH-5030/5031 Series is

• After soldering, remove the protective tape as shown

Failure to comply with these instructions may result in

product damage.

atmosphere being monitored.

factory-shipped with a protective tape on the cover

(sensing face). This tape must remain in place during

soldering.

below to activate the sensor.

Use proper ESD protection.

Using covered fingers or tweezers to ensure that no

foreign debris falls into the filter, sensor cover or die, grip

the overhanging front edge of the protective tape and peel

it back from the top surface of the sensor.

Ensure the complete rectangle of protective tape is

removed.

50038351

ISSUE 1

C [482

F].

Related parts for HIH-5031-001S

HIH-5031-001S Summary of contents

Page 1

... Failure to comply with these instructions may result in product damage. CAUTION IMPROPER SOLDERING • For better product reliability, the HIH-5030/5031 Series is factory-shipped with a protective tape on the cover (sensing face). This tape must remain in place during soldering. • After soldering, remove the protective tape as shown below to activate the sensor ...

Page 2

... Non-condensing environment. When liquid water falls on the humidity sensor die, output goes to a low rail condition indicating no humidity. 4. Total accuracy including interchangeability is ±3 %RH. Figure 2. Operating Environment (Non-condensing environment for HIH-5030 catalog listings only.) 2 Honeywell • Sensing and Control Minimum Typical Maximum -7 – ...

Page 3

... HIH-5030/5031 Series Figure 3. Storage Environment (Non-condensing environment for HIH-5030 catalog listings only.) Figure 4. HIH-5030 Mounting Dimensions (For reference only. mm/[in]) Figure 5. HIH-5031 Mounting Dimensions (For reference only. mm/[in]) 50038351 Issue 1 Honeywell • Sensing and Control 3 ...

Page 4

... HIH-5030/5031 Series Figure 6. Tape and Reel Dimensions (For reference only. mm/[in]) WARRANTY/REMEDY Honeywell warrants goods of its manufacture as being free of defective materials and faulty workmanship. Honeywell’s standard product warranty applies unless agreed to otherwise by Honeywell in writing; please refer to your order acknowledgement or consult your local sales office for specific warranty details ...

Related keywords

HIH-5031-001S datasheet
HIH-5031-001S data sheet
HIH-5031-001S pdf datasheet
HIH-5031-001S component
HIH-5031-001S part
HIH-5031-001S distributor
HIH-5031-001S RoHS
HIH-5031-001S datasheet download