M2032SS1A01 NKK Switches, M2032SS1A01 Datasheet - Page 2

• Manufacturer Part Number: M2032SS1A01
• Manufacturer: NKK Switches

Specifications of M2032SS1A01

• Pole Throw Configuration: 3PDT
• Switch Configuration: ON None ON
• Actuator Style: Bat Toggle
• Current Rating (max): 6A
• Ac Voltage Rating (max): 250VVAC
• Dc Voltage Rating (max): 30VVDC
• Power Rating (max): 0.4W
• Contact Material: Silver Alloy
• Contact Plating: Gold
• Mechanical Life: 100000
• Operating Temperature Min Deg. C: -30C
• Operating Temperature Max Deg. C: 85C
• Mounting Style: Panel
• Lead Free Status / RoHS Status: Compliant

General Specifi cations
Electrical Capacity (Resistive Load)
Other Ratings
Materials & Finishes
Environmental Data
Installation
Processing
Standards & Cer tifications
NKK Switches • email: [e-mail] • Phone [phone] • Fax [phone] • www.nkkswitches.com
R
Logic/Power Level (code A):
Nominal Operating Force:
Flammability Standards:
Operating Temp Range:
Power Level (code W):
Insulation Resistance:
Logic Level (code G):
Stationary Contacts:
Movable Contactor:
Contact Resistance:
Dielectric Strength:
Movable Contacts:
Mounting Torque:
Mechanical Life:
Angle of Throw:
UL Recognized:
CSA Certifi ed:
Electrical Life:
Soldering:
Terminals:
Vibration:
Humidity:
Cleaning:
Bushing:
Sealing:
Toggle:
Shock:
Case:
6A @ 125V AC & 3A @ 250V AC
4A @ 30V DC for On-None-On & On-None-Off; 3A @ 30V DC for all other circuits
0.4VA maximum @ 28V AC/DC maximum (Applicable Range 0.1mA ~ 0.1A @ 20mV ~ 28V)
Combines W & G ratings
Note: Find additional explanation of dual rating & operating range in Supplement section.
10 milliohms maximum for silver; 20 milliohms maximum for gold
1,000 megohms minimum @ 500V DC
1,000V AC minimum between contacts for 1 minute minimum;
1,500V AC minimum between contacts and case for 1 minute minimum
100,000 operations minimum; 50,000 operations minimum for fl at, locking, & splashproof devices
25,000 operations minimum for silver; 50,000 operations minimum for gold;
50,000 operations minimum for silver at 3A @ 125V AC
3.92N for Single Pole; 4.41N for Double Pole; 6.86N for Three Pole; 7.85N for Four Pole
25°
Brass with chrome plating
Brass with nickel plating
Diallyl phthalate resin (UL94V–0)
Phosphor bronze with silver or gold plating
Silver alloy (code W); copper with gold plating (code G); or silver alloy with gold plating (code A)
Silver with silver plating (code W); copper or brass with gold plating (code G);
or silver with gold plating (code A)
Copper or brass with silver plating; or copper or brass with gold plating
–30°C through +85°C (–22°F through +185°F)
90 ~ 95% humidity for 96 hours @ 40°C (104°F)
10 ~ 55Hz with peak-to-peak amplitude of 1.5mm traversing the frequency range
& returning in 1 minute; 3 right angled directions for 2 hours
50G (490m/s
Panel seal bushing options B3 & D3 meet IP67 of IEC60529 Standards.
3.0Nm (26.55 lb
1.5Nm (13 lb
For all Gold Contacts & Circuits 1, 3, 8, & 9, see Wave Soldering Profi le A in Supplement section.
Manual Soldering: 4 seconds max. @ 410°C max. Note: Lever must be in OFF (center) position.
For Silver Contact Circuits 2 & 4 through 7: Wave Soldering: 5 seconds maximum @ 270°C maximum.
Manual Soldering: 3 seconds max. @ 350°C max.
These devices are not process sealed. Hand clean locally using alcohol based solution.
See Cleaning Specifi cations in Supplement section.
UL94V–0 for case
All models recognized at 6A @ 125V AC or 3A @ 250V AC or
0.4VA maximum @ 28V DC maximum; UL File No. WOYR2.E44145;
add “/U” to end of part number to order UL mark on switch.
All models recognized at 6A @ 125V AC or 3A @ 250V AC or
0.4VA maximum @ 28V maximum; CSA File No. 023535-0-000;
add “/C” to end of part number to order CSA mark on switch.
•
2
in) double nut & 0.7Nm (6 lb
) acceleration (tested in 6 right angled directions, with 5 shocks in each direction)
•
in) double nut for large bushing;
Miniature Toggles
•
in) single nut for all other bushings
Support Bracket:
Frame:
Stainless steel
Steel with tin plating
Series M
3-05