AT89STK03 Atmel, AT89STK03 Datasheet
AT89STK03
Specifications of AT89STK03
AT89STK03 Summary of contents
Page 1
AT89STK-03 Starter Kit for AT8xC5122 & AT83C5123 .............................................................................................. Hardware User Guide ...
Page 2
AT89STK-03 Hardware User Guide Section 1 Introduction ........................................................................................... 1-1 1.1 Features ....................................................................................................1-1 Section 2 Hardware Description ........................................................................... 2-5 2.1 Block Diagram...........................................................................................2-5 2.2 Power Supply ............................................................................................2-6 2.2.1 Regulator Output Voltage Selection & Power On...............................2-7 2.3 C51 Settings .............................................................................................2-7 2.3.1 INT1 Switch ...
Page 3
AT89STK-03 Hardware User Guide Section 4 Schematics ......................................................................................... 4-27 4.1 Bill of Materials........................................................................................4-35 Section 5 Document Revision History ................................................................ 5-37 Table of Contents ii 7609B–SCR–11/06 ...
Page 4
Features AT89STK-03 Hardware User Guide This document describes the MCU demonstration board included in AT89STK-03 Starter Kit dedicated to the AT8xC5122 & AT83C5123 Smart Card Reader microcontrollers. This board enables to test the microcontrollers by using demonstration software and/or ...
Page 5
Introduction Figure 1-1. AT8xC5122 & AT83C5123 Evaluation Board Power Converter input Fuse bypass Fuse 9V Battery Input Regulator bypass Lab. Power Supply input SPI ALE Led Crystal E2PROM location 1-2 7609B–SCR–11/06 Regulator Output Voltage selection Power Supply Power Switch config ...
Page 6
Figure 1-2. Default Configuration : Component Side - Jumper Config AT89STK-03 Hardware User Guide Introduction Solder Side 7609B–SCR–11/06 1-3 ...
Page 7
Introduction Figure 1-3. Default Configuration : Solder Side - Jumper Configuration 1-4 7609B–SCR–11/06 AT89STK-03 Hardware User Guide ...
Page 8
Block Diagram AT89STK-03 Hardware User Guide Figure 2-1. AT8xC5122 & AT83C5123 demonstration board components RS232 POWER Supply Reset EA INT1 SCIB Master Smart Card Section 2 Hardware Description USB SPI AT8xC5122 EEPROM LED SIM SIM Smart Card 2-5 7609B–SCR–11/06 ...
Page 9
Hardware Description 2.2 Power Supply 2-6 7609B–SCR–11/06 The on-board power supply electronics enable various power supply configurations. The power source can be: – VBus from USB interface (USB connector) – An external power converter (9V DC connector) – 9V Battery ...
Page 10
Regulator Output Voltage Selection & Power On 2.3 C51 Settings 2.3.1 INT1 Switch 2.3.2 EA Jumper 2.3.3 ALE led 2.3.4 Reset 2.3.5 Crystal 2.4 Features Description 2.4.1 LEDs Settings AT89STK-03 Hardware User Guide Power On/Off ON OFF The 3.6V ...
Page 11
Hardware Description 2.4.2 USB Peripheral 2.4.3 SPI 2.4.4 RS232 2.4.5 SIM Alternate Card 2.4.6 PLL Filter 2-8 7609B–SCR–11/06 Name Color Description General purpose led - Connected to P3.6 - Enabled by LED2 jumper or SW21 LED2 Green solder pad General ...
Page 12
EEPROM Settings 2 headers AT89STK-03 Hardware User Guide This MCU demonstration board supports different versions of the AT8XC5122 and AT83C23 microcontrollers: - Flash versions - CRAM versions - ROM versions and different versions of embedded bootloaders ...
Page 13
AT89STK-03 Hardware User Guide This section applies only to versions AT85C5122, AT85EC5122 and AT89C5122. The method to program the part depends on the version of the bootloader which is embed- ded in a ROM memory. The bootloader version is defined ...
Page 14
Part Programming 3.1 Bootloader DPW 3.1.1 ISP mode (In System Programming ) Table 3-1. Programming the MCU with FLIP Interface Perform the following actions USB DEMO BOARD CONFIGURATION - Set the POWER switch in OFF position - Remove any E2P ...
Page 15
Table 3-1. Programming the MCU with FLIP Interface Perform the following actions RS232C DEMO BOARD CONFIGURATION - Set the POWER switch in OFF position - Remove any USB cable connected to demoboard - Remove any E2P present on DIP socket ...
Page 16
Part Programming Table 3-2. Programming the E2PROM with FLIP Interface Perform the following actions USB DEMO BOARD CONFIGURATION interface - Set the POWER switch in OFF position - Remove any E2P present on DIL8 socket - Connect a USB cable ...
Page 17
Table 3-2. Programming the E2PROM with FLIP Interface Perform the following actions RS232C DEMO BOARD CONFIGURATION interface - Set the POWER switch in OFF position - Remove any E2P present on DIL8 socket - Connect a USB cable between demo ...
Page 18
Part Programming 3.2 Bootloader DRV 3.2.1 ISP Mode 3.2.2 Execution mode 3-16 7609B–SCR–11/06 Ensure you are familiar with the DRV bootloader datasheet before programming the part. Configure the MCU demonstration board following Table 2-2 on page 9. CRAM version The ...
Page 19
Table 3-3. Programming with bootloader DRV External E2P Interface Perform the following actions Not USB DEMO BOARD CONFIGURATION Present - Set the POWER switch in OFF position (AT85 like) - Connect an USB cable between demo board and PC. If ...
Page 20
Part Programming Table 3-3. Programming with bootloader DRV External E2P Interface Perform the following actions Present USB DEMO BOARD CONFIGURATION interface (AT89 like) - Set the POWER switch in OFF position - Connect a USB cable between demo board and ...
Page 21
Table 3-3. Programming with bootloader DRV External E2P Interface Perform the following actions Not RS232C DEMO BOARD CONFIGURATION present - Set the POWER switch in OFF position (AT83 like) - Remove any USB cable connected to demoboard - Connect a ...
Page 22
Part Programming Table 3-3. Programming with bootloader DRV External E2P Interface Perform the following actions Present RS232C DEMO BOARD CONFIGURATION interface (AT85 like) - Set the POWER switch in OFF position - Remove any USB cable connected to demoboard - ...
Page 23
Bootloader DSU 3.3.1 ISP Mode 3.3.2 Execution mode AT89STK-03 Hardware User Guide The DSU bootloader fixes a USB bug present in the DRV bootloader. Therefore the DSU bootloader has the same features as the DRV bootloader. Ensure you are ...
Page 24
Part Programming Table 3-4. Programming with bootloader DSU E2PROM Interface Perform the following actions Not USB DEMO BOARD CONFIGURATION present - Set the POWER switch in OFF position (AT85 like) -- Connect a USB cable between demo board and PC. ...
Page 25
Table 3-4. Programming with bootloader DSU E2PROM Interface Perform the following actions Present USB DEMO BOARD CONFIGURATION (AT89 like) - Set the POWER switch in OFF position - Connect a USB cable between demo board and PC RS232C ...
Page 26
Part Programming Table 3-4. Programming with bootloader DSU E2PROM Interface Perform the following actions Not RS232C DEMO BOARD CONFIGURATION present - Set the POWER switch in OFF position (AT85 like) - Remove any USB cable connected to demoboard - Connect ...
Page 27
Table 3-4. Programming with bootloader DSU E2PROM Interface Perform the following actions Present RS232C DEMO BOARD CONFIGURATION (AT89 like) - Set the POWER switch in OFF position - Remove any USB cable connected to the demoboard - Connect a RS232C ...
Page 28
AT89STK-03 Hardware User Guide Section 4 Schematics 4-27 7609B–SCR–11/06 ...
Page 29
Schematics Figure 4-1. Power Supply Section 4-28 7609B–SCR–11/ GND 7 GND 6 GND 3 GND 2 GND AT89STK-03 Hardware User Guide ...
Page 30
Figure 4-2. PLCC68 CPU Section AT89STK-03 Hardware User Guide AVCC 68 VCC CVSS 30 AVSS 66 VSS 25 NC1 ...
Page 31
Schematics Figure 4-3. PLCC28_VQFP64 CPU Section 4-30 7609B–SCR–11/06 AVCC CVSS 28 14 AVSS 26 VCC VSS 15 11 AVCC 55 VCC 20 CVSS 19 AVSS 53 VSS 16 AT89STK-03 Hardware User Guide ...
Page 32
Figure 4-4. Smart Card Schema AT89STK-03 Hardware User Guide 1 1 Size Full ctor ...
Page 33
Schematics Figure 4-5. E2P LEDs Section VCC 4-32 7609B–SCR–11/06 GND ...
Page 34
Figure 4-6. Comm Interfaces Section 1 1 AT89STK-03 Hardware User Guide GND 15 C2- 5 Schematics 4-33 7609B–SCR–11/06 ...
Page 35
Schematics Figure 4-7. C51 Generic Bus 4-34 7609B–SCR–11/ AT89STK-03 Hardware User Guide ...
Page 36
Bill of Materials Reference C12,C13,C35,C36 C26,C10 C25,C7 C1,C3,C5,C6,C9,C14,C15, C19,C20,C21,C22,C23,C24, C27,C28,C30,C32,C34 C31,C11 C2 C8,C4 R11,R12,R29,R30 R5 R2,R7,R13,R15,R21,R22, R23,R24,R25,R26,R27 R14 R16,R9 R17,R18,R19,R20 R1,R6, L2,L1 D4,D5,D6,D7,D8,D9,D10, D11,D12 D13, J19 J22 ...
Page 37
AT89STK-03 Hardware User Guide Document Revision History Changes from 4302A to 4302B 1. Updated document to reflect version 1.2.0 of MCU demonstration board. Section 5 5-37 7609B–SCR–11/06 ...
Page 38
... Atmel does not make any commitment to update the information contained herein. Unless specifically providedot- herwise, Atmel products are not suitable for, and shall not be used in, automotive applications. Atmel’s products are not intended, authorized, or warranted for use as compo- nents in applications intended to support or sustain life. © ...