UM9602 MICROSEMI, UM9602 Datasheet
UM9602
Specifications of UM9602
Available stocks
Related parts for UM9602
UM9602 Summary of contents
Page 1
... MHz bandwidth and with a transmitter insertion loss of less than 0.4 dB. This switch can safely handle transmitter power levels up to 100 watts at infinite SWR. IMPORTANT: For the most current data, consult MICROSEMI’s website: http://www.microsemi.com UM9601-9604 SPST Insertion Loss Frequency ...
Page 2
... Min 0.4 0.6 150k 1.2 1.0 0.85 150 Microsemi UM9601 – UM9608 UM9605-UM9608 P θ 37.5 C/W 0 400 V UM9602 UM9604 UM9606 UM9608 UM9605-UM9608 Typ Max Units 1.5 1.7 Ω Ω 0.5 pF µs 0.95 V µm Condition I = 100 100 MHz Vr = 100 100 MHz Vr = 100 V ...
Page 3
... Rev. 0, 2006-01-17 FOR MICROSTRIP 900 MHz ANTENNNA SWITCHES AND MICROWAVE APPLICATIONS Recommended Types UM9601 (Affixes to microstrip ground plane) UM9603 (Affixes to microstrip backing plate) UM9602 UM9604 UM9605 (Affixes to microstrip ground plane) UM9607 (Affixes to microstrip backing plate) UM9606 UM9608 DIODE RESISTANCE vs DIODE CURRENT TYPICAL ...
Page 4
... UM9601 – UM9608 FOR MICROSTRIP 900 MHz ANTENNNA SWITCHES AND MICROWAVE APPLICATIONS PULSE THERMAL IMPEDANCE TYPICAL UM9605 - UM9608 UM9601 - UM9604 - PULSE WIDTH (sec) Rp VERSUS VOLTAGE AND FREQUENCY UM9601 - UM9604 TYPICAL REVERSE VOLTAGE (V) Microsemi F=100 MHz F=500 MHz F=1 GHz F=3 GHz Page 4 ...
Page 5
... UM9601 – UM9608 FOR MICROSTRIP 900 MHz ANTENNNA SWITCHES AND MICROWAVE APPLICATIONS POWER RATING TYPICAL UM9601 - UM9604 UM9605 - UM9608 100 125 HEAT SINK TEMPERATURE ( VOLTAGE AND FREQUENCY UM9605-UM9608 TYPICAL REVERSE VOLTAGE (Vr) Microsemi O S 150 175 100 MHz 500 MHz 1 GHz 3 GHz 3 10 Page 5 ...
Page 6
... Copyright 2005 Rev. 0, 2006-01-17 UM9601 – UM9608 FOR MICROSTRIP 900 MHz ANTENNNA SWITCHES AND MICROWAVE APPLICATIONS TYPICAL SECOND ORDER THIRD ORDER (MHz) FORWARD BIAS CURRENT AT 20 dBm PER CHANNEL TYPICAL MHz MHz Fa = 7.4 MHz Fb = 7.6 MHz (mA) Microsemi Page 6 ...
Page 7
... UM9601 – UM9608 FOR MICROSTRIP 900 MHz ANTENNNA SWITCHES AND MICROWAVE APPLICATIONS DISTORTION vs INPUT POWER PER CHANNEL Fa = 7.4 MHz Fb = 7.6 MHz 10 20 INPUT POWER PER CHANNEL (dBm) TYPICAL THIRD ORDER SECOND ORDER MHz MHz P = 20dBm PER CHANNEL 10 REVERSE VOLTAGE (Vr) Microsemi MHz MHz Page 7 ...
Page 8
... UM9601 UM9602 UM9605 UM9606 Copyright 2005 Rev. 0, 2006-01-17 UM9601 – UM9608 FOR MICROSTRIP 900 MHz ANTENNNA SWITCHES AND MICROWAVE APPLICATIONS UM9603 UM9604 UM9607 UM9608 Microsemi Page 8 ...
Page 9
... In this case the isolation of each section will be twice the dB value of the switch. The insertion loss due to the diodes should be less than twice the insertion loss of an SPST section due to the transforming effect of the quarter-wave line on the capacitance of a single diode. Microsemi Page 9 ...
Page 10
... MICROSTRIP SPST SWITCH DIODE CURRENT = 100 Copyright 2005 Rev. 0, 2006-01-17 FOR MICROSTRIP 900 MHz ANTENNNA SWITCHES AND MICROWAVE APPLICATIONS ISOLATION vs FREQUENCY .025" (.635mm) ALUMINA TYPICAL UM9601 - UM9604 UM9605 - UM9608 FREQUENCY (GHz) TYPICAL UM9601 - UM9604 UM9605 - UM9608 FREQUENCY (GHz) Microsemi UM9601 – UM9608 Page 10 ...
Page 11
... Installation in Microstrip The cup type flange on the UM9601, UM9602, UM9605, and UM9606 is designed to be affixed to the ground plane surface of a microstrip board. The UM9603, UM9604, UM9607, and UM9608 were designed to be affixed to a backing plate as shown. It was experimentally determined that at frequencies greater than 2 GHz the anode of the diode should be approximately 0.010” ...
Page 12
... MAX. TRANSMITTER POWER vs FORWAD CURRENT FOR UM9601/UM9401 900 MHz MICROSTRIP ANTENNA SWITCH TYPICAL 100 AMBIENT TEMPERATURE Microsemi For a perfectly match antenna the power Ohms SWR = INFINITE 200mA 100 125 150 175 Page 12 ...
Page 13
... SWR = 1) C. Transmitter Insertion Loss 0 Receiver Isolation Harmonic Distortion - 100 watts) T Copyright 2005 Rev. 0, 2006-01-17 UM9601 – UM9608 FOR MICROSTRIP 900 MHz ANTENNNA SWITCHES AND MICROWAVE APPLICATIONS II. Receive State (zero Bias) A. Receiver Isolation Loss 0.6-0 Intermodulation Distortion -100 dBm IN Microsemi Page 13 ...
Page 14
... LOSS (If=0) 0.6 If=20 mA If=50 mA 0.4 0.2 0.0 700 750 800 850 FREQUENCY (MHz) RECEIVER ISOLATION vs FREQUENCY AND DIODE CURRENT TYPICAL 35 100 700 750 800 850 FREQUENCY (MHz) Microsemi O S TRANSMITTER INSERTION LOSS (If=100 mA) 900 950 1000 900 950 1000 Page 14 ...
Page 15
... Chip Capacitor D1 PIN Diode D2 PIN Diode J1-J3 SMA Connector Substrate Copyright 2005 Rev. 0, 2006-01-17 UM9601 – UM9608 FOR MICROSTRIP 900 MHz ANTENNNA SWITCHES AND MICROWAVE APPLICATIONS Erie 1270-016 Vitramon VJ0805A300KF Microsemi UM9401 Microsemi UM9601 Cableware 971-028 Vectronics Microwave 79-9081-0401 Microsemi Page 15 ...
Page 16
... Copyright 2005 Rev. 0, 2006-01-17 UM9601 – UM9608 FOR MICROSTRIP 900 MHz ANTENNNA SWITCHES AND MICROWAVE APPLICATIONS NOTES: Microsemi Page 16 ...