LSZ1AC Honeywell, LSZ1AC Datasheet

LSZ1AC

Manufacturer Part Number

LSZ1AC

Description

Switch Hardware Operating Head Limit Switch

Manufacturer

Honeywell

Type

Operating Headr

Datasheets

1.LSZ1AC.pdf (4 pages)

2.LSZ1AC.pdf (1 pages)

Specifications of LSZ1AC

Switch Type

Limit Switch

Lead Free Status / RoHS Status

Compliant

Current page: 1 of 4
Download datasheet (433Kb)

Installation Instructions for the

HDLS Series Switches

MOUNTING

All Heavy Duty Limit Switches (HDLS) have exactly the

same mounting dimensions. Mount by either of two

methods: (a) use two #10 screws from the front, or (b)

use two #10-32 UNF screws from the back. HDLS offers

the advantage of front mount construction. The

electrician will find a complete switch, with no parts

missing and ample wiring space.

With plug-in construction, wiring and conduit connection

is made to the base receptacle. This feature also

reduces downtime, since plug-in unit can be removed

without disconnecting wiring or conduit.

To mount either switch, merely tighten mounting screws,

tighten plug-in unit or cover screws, and make sure

conduit section is sealed. Use of sealant (teflon tape,

pipe dope, etc.) is recommended to seal conduit

connection.

Because of moisture condensation problems, it is not

good practice to mount the switch upside down or at the

low point of conduit runs.

Single-Pole – Plug-in Type

Sensing and Control

PERSONAL INJURY

DO NOT USE these products as safety or emergency

stop devices or in any other application where failure

of the product could result in personal injury.

Failure to comply with these instructions could

result in death or serious injury.

WARNING

Double-Pole – Non

Plug-in Type

Sealing

Enclosure Type

Rated Operational Voltages (Ue) and Currents (Ie)

120 Vac

600 Vac

125 Vdc

250 Vdc

WIRING

Use size #12AWG or smaller solid or

stranded wire to connect to the

pressure type connector terminals.

Spades may be up to .312" wide,

rings up to .312" dia. With spade or

ring type connections, preinsulated

connectors or heat-shrinkable tubing

should be used to provide insulation

between terminals. Circuit diagram is

shown on the nameplate.

It will be easier to wire the double-

pole units by connecting lead wires to

the terminals nearest the conduit opening first. A

grounding screw is located in the housing near the

conduit opening.

Switch units with an indicator light in the cover are

furnished with the lead wires from the light connected to

the normally-open male terminals (#3 and #4) unless

otherwise specified on the order. Wires can be

unsoldered and reconnected to the normally-closed male

terminals or they can be ordered connected to the

normally-closed terminals by using a modification code

(refer to Catalog 40). Always connect these wires to the

same set of terminals used for the load. Across the

normally open male terminals (#3 and #4) the light will

be On (Fig. 1). Across the normally closed terminals (#1

and #2) the light will be Off.

IP67/68

1, 3, 3R, 4, 4X, 6, 6P, 12, 13

6 A

1.2 A

0.22 A

0.11 A

PK 81116

ISSUE 2

Related parts for LSZ1AC

LSZ1AC Summary of contents

Page 1

... Failure to comply with these instructions could result in death or serious injury. MOUNTING All Heavy Duty Limit Switches (HDLS) have exactly the same mounting dimensions. Mount by either of two methods: (a) use two #10 screws from the front, or (b) use two #10-32 UNF screws from the back. HDLS offers the advantage of front mount construction ...

Page 2

... Referring to Fig. 3, slide cam all the way back, so cam is free to rotate on the shaft. 2 Honeywell • Sensing and Control 4. Using a screwdriver or similar tool, rotate cam to desired actuating position (Fig and 6.) 5. Slide cam all the way forward to its original position, and close hinged cover ...

Page 3

... LSZ3K LSZ1F LSZ3L LSF1G ** LSZ1H LSZ3K LSZ1H LSZ3 L LSZ1JGA LSZ3 L LSZ1JGM LSZ3 K LSZ1JGA LSZ3 L LSZ1JGM LSZ3 L LSZ1KHA LSZ3 K LSZ1KHA LSZ3 L LSZ1L LSZ3 M LSZ1M LSZ3M LSZ1N ** LSZ1N * * LSZ1P LSZ3 K LSZ1P LSZ3 L LSZ1R LSZ3 K LSZ1R LSZ3 L LSZ1U LSZ3 K Honeywell • Sensing and Control 3 ...

Page 4

... LSZ1S LSZ3H LSZ1T LSZ3H LSZ1AB LSZ3A LSZ1AC LSZ3A SALES AND SERVICE Honeywell serves its customers through a worldwide network of sales offices, representatives and distributors. For application assistance, current specifications, pricing or name of the nearest Authorized Distributor, contact your local sales office or: E-mail: info.sc@honeywell.com Internet: www ...

Related keywords

LSZ1AC datasheet
LSZ1AC data sheet
LSZ1AC pdf datasheet
LSZ1AC component
LSZ1AC part
LSZ1AC distributor
LSZ1AC RoHS
LSZ1AC datasheet download