LA00HLW TELEDYNE, LA00HLW Datasheet

LA00HLW

Manufacturer Part Number

LA00HLW

Description

Relay SSR 16mA 32V DC-IN 7.5A 250V AC-OUT 6-Pin (6+Tab)

Manufacturer

TELEDYNE

Datasheet

1.LA00HLW.pdf (4 pages)

Specifications of LA00HLW

Input Type

I/o Isolation Voltage

1250(RMS) V

Maximum Input Current

16 mA

Maximum Output Current

7.5(RMS) A

Maximum Input Voltage

32 V

Maximum Output Voltage

250(RMS) V

Output Type

Current page: 1 of 4
Download datasheet (771Kb)

KA/LA 78

Part Number* Relay Description

KA00HF

KA58HF

LA00HL

LA58HL

* The Y suffix denotes parameters tested to MIL-PRF-28750 test methods.

ELECTRICAL SPECIFICATIONS

(-55°C TO +110°C UNLESS OTHERWISE SPECIFIED)

2 Terminal Configuration (See Fig. 1)

Input Voltage (See note 2)

Input Current (See Figure 1)

Turn-Off Voltage (Guaranteed Off)

Turn-On Voltage (Guaranteed On)

Reverse Voltage Protection

3 Terminal Configuration (See Fig. 1)

Bias Voltage (See note 2)

Bias Current (V

Control Voltage Range

Control Current (at 5 Vdc)

Turn-On Control Voltage

Turn-Off Control Voltage

Load Voltage

Frequency Range

Continuous Load Current (See Figure 3)

Output Voltatge Drop

The W suffix denotes parameters tested to Teledyne specifications.

KA and LA without Heat Sink

LA with Heat Sink

= 5 Vdc

2 A, 250 Vrms, AC Solid-State Relay

2 A, 250 Vrms, AC Solid-State Relay with Thermal

Protection and Thermal TRIP Status

7.5 A, 250 Vrms, AC Solid-State Relay

7.5 A, 250 Vrms, AC Solid-State Relay with Thermal

Protection and Thermal TRIP Status

INPUT (CONTROL) CHARACTERISTICS

=32 Vdc)

OUTPUT (LOAD) SPECIFICATIONS

SPECIFICATIONS ARE SUBJECT TO CHANGE WITHOUT NOTICE

Min

3.8

3.2

Max

250

440

-32

0.3

1.5

2.0

7.5

1.2

mA dc

Units

µAdc

Vrms

Arms

Vrms

Vdc

2.0 to 7.5A, 250 Vrms Optically Isolated

FEATURES/BENEFITS

• Available with thermal protection

• Optical Isolation: Isolates control

• Fully Floating Output: Eliminates

• Buffered Control: Relay can be

• Integral Snubber Circuit: Enhances

DESCRIPTION

The Series KA/LA solid-state relays

(SSRs) is designed for use in AC

power switching applications where

safety and reliability are primary

concerns. These SSRs are rated for

load voltages up to 250 Vrms from 40

to 440 Hz and are ideal for resistive

and reactive loads with power factors

as low as 0.2. Inverse parallel SCRs

are configured for zero voltage turn on.

Optical isolation to 1250 Vrms between

the control (input) and load (output)

allows the load to be safely controlled

by logic circuitry. The KA/LA series is

available with thermal protection and

thermal TRIP status. In case of a

thermal runaway condition, the SSR

will shut down the output switch and

latch off until the input is reset and the

junction temperature returns to a safe

level. When the output does latch off,

the TRIP status line will yield a logic

level output indicating the protection

state of the SSR. This feature provides

the user with failure mode indication

while enhancing the system diagnostic

capability. These SSRs are available to

the Y screening level of MIL-PRF-

28750 and are packaged in low-profile

hermetically sealed cases.

and thermal TRIP status: Provides

self-protection from thermal

runaway conditions and indicates

protection state for system BIT.

elements from load transients with

reduced EMI.

ground potential loops and allows

the output to sink or source current.

controlled directly from TTL or

CMOS logic circuits.

dV/dt capability while minimizing

EMI.

Series KA/LA

AC Solid-State Relay

KA/LA\072002\Q1

Related parts for LA00HLW

LA00HLW Summary of contents

Page 1

... LA58HL 7.5 A, 250 Vrms, AC Solid-State Relay with Thermal Protection and Thermal TRIP Status * The Y suffix denotes parameters tested to MIL-PRF-28750 test methods. The W suffix denotes parameters tested to Teledyne specifications. ELECTRICAL SPECIFICATIONS (-55°C TO +110°C UNLESS OTHERWISE SPECIFIED) INPUT (CONTROL) CHARACTERISTICS 2 Terminal Configuration (See Fig. 1) ...

Page 2

... MIL-PRF-28750 0.2 MECHANICAL SPECIFICATIONS 9 10 Ohm 15 pF 1250 Vrms o Max) 125 C C/W JC Output (Load) State On Tripped (Off) Off Non-applicable condition Min Max Units 32 Vdc 10 µAdc 10 mAdc DIMENSIONS ARE SHOWN IN INCHES 0.4 Vdc (800) 284-7007 • www.teledynerelays.com Series KA/LA (MILLIMETERS) KA/LA 79 KA/LA\072002\Q1 ...

Page 3

... Transient suppression must be used to limit the voltage to < 500 Vpeak when switching inductive loads. KA/LA 80 SPECIFICATIONS ARE SUBJECT TO CHANGE WITHOUT NOTICE Min Max Units o -55 +110 C -55 +125 o C 1500 g 10 3000 Hz 5000 g WIRING CONFIGURATION Series KA/LA FIGURE 1 (See Note 1 & 2) © 2002 TELEDYNE RELAYS KA/LA\072002\Q1 ...

Page 4

... TELEDYNE RELAYS TYPICAL VOLTAGE DROP VS LOAD CURRENT OF LA SERIES WITH 1 SERIES LIMIT BIAS RESISTOR VS BIAS VOLTAGE FIGURE 6 (SEE NOTE 2) TYPICAL THERMAL TRIP TIME KA58HF AND LA58HL (800) 284-7007 • www.teledynerelays.com Series KA/LA ° C/W HEATSINK FIGURE 5 FIGURE 7 KA/LA 81 KA/LA\072002\Q1 ...

Related keywords

LA00HLW datasheet
LA00HLW data sheet
LA00HLW pdf datasheet
LA00HLW component
LA00HLW part
LA00HLW distributor
LA00HLW RoHS
LA00HLW datasheet download