1-179228-1 TE Connectivity, 1-179228-1 Datasheet
1-179228-1
Specifications of 1-179228-1
Available stocks
Related parts for 1-179228-1
1-179228-1 Summary of contents
Page 1
... Scope: 1.1 Contents: This specification covers the requirements for product performance, test methods and quality assurance provisions of AMP Common Termination (CT), Connector, 2mm Pitch, Crimp Type. The applicable product description and part numbers are as shown in Fig.1: Product Part No. X-179228-X X-179227-X X-179518-X X-179609-X X-179610-X 2 ...
Page 2
... AMP Shanghai Ltd. ASHL-0005- ES REV B : 6/6 Nylon (UL94 V-0) : Pretinned Phosphor Bronze (0.8um min. thick) : Phosphor Bronze (0.5um min. thick Au Plated over 1~2um thick Nickel underplate) : 6/6 Nylon (UL94 V-0) : Pretin lead Brass (0.8um min. thick solder-plated over 0.5um min. thick copper underplate) : 6/6 Nylon GF Type (UL94 V-0) : Pretin lead Brass (0 ...
Page 3
... A. Board Thickness B. Hole Diameter 3.6 Applicable Panel Thickness: 0.8~1.6mm (To be used for post header and relay) 3.7 Performance Requirements and Test Descriptions: The product shall be designed to meet the electrical, mechanical and environmental performance requirements specified in Fig.2, Para. 3.8. All tests shall be performed at ambient temperature unless otherwise specified ...
Page 4
... The load is applied in the axial and lateral directions as specified. Measure the force required to mount contact on housing. Apply axial load to contact by operating at a rate of 100mm a minute. Apply an axial pull-off load to post contact mounted on housing and measure the force required to dislodge post from the housing ...
Page 5
... Product shall be confirming to the requirements of applicable product drawing and Application Specification 114-5179. Electrical Performance Requirements 10 m Max. (Initial Max. (Final) Connector must withstand test potential of 1.0 kV (AC) for 1 minute. Current leakage must be 5.0mA Max. 1000 M Min. (Initial max. under loaded specified current. See Fig. 3. ...
Page 6
... Resistance (low level) (Final) must meet visual & electrical requirements, which applicable. Fig. 2 (To be continued) PAGE Procedures Subject mated connectors to 10- 55-10 Hz traversed in 1 minute at 1.52 mm amplitude 2 hours each of 3 mutually perpendicular planes. MIL-STD-202, Method 201, Condition A. Subject mated connectors to 2 490.3 m/s halfsine shock pulses of 11milisecond duration ...
Page 7
... SMT product mounted on printed circuit boards to solder reflow as like Fig. 7. See Para. 3.8.3 (11-1) and Para. 3.8.3 (11-2) Subject connector assembly to 30 cycles of repeated mating/unmating at a rate of 10 cycles a minute. Subject mated connector to temperature changes between and 65 C with 95 % R.H. ...
Page 8
... Tyco Electronics AMP Shanghai Ltd. ASHL-0005- ES REV B Fig.3 Fig.4 Fig.5 Fig.7 PAGE Fig.6 Document No. REV 108-5408 LOC B ES ...
Page 9
... Test Specimens: The test specimens to be used for the performance evaluation testing, shall be prepared in accordance with AMP Application Specification, 114-5179, Termination of AMP CT Connector Pitch, Crimp Type II, by using the samples selected from the current production at random, and conforming to the requirements of the applicable product drawing. ...
Page 10
... The applicable product descriptions and part numbers are as shown in Appendix 1. Product Part No. X-173979-X Post Header, Horizontal (H) X-176931-X Post Header, Horizontal (H), in Tube X-176303-X Post Header, Horizontal (H), w/o Kink X-176304-X Post Header, Horizontal (H), w/o Kink, in Tube X-173981-X Post Header, Vertical (V) X-175519-X Post Header, Vertical (V), in Tube ...
Page 11
... Post Header, Vertical (V), SMT Type, Box Type, on Embossment Tape Tyco Electronics AMP Shanghai Ltd. ASHL-0005- ES REV B Product Descriptions Appendix 1 PAGE No. of Pos. 2~6, 8 Pos. 2~6, 8 Pos. 2~6, 8 Pos 8~11 Pos. 7~10, 13 Pos. Document No. REV 108-5408 2~5 Pos. 6 Pos. 2~9 Pos. 2~9 Pos. 2~9 Pos. 2~9 Pos. 3 Pos. ...