MICRO-MATCH PBC.16P

1-215570-6

Manufacturer Part Number1-215570-6
DescriptionMICRO-MATCH PBC.16P
ManufacturerTE Connectivity
1-215570-6 datasheets
 

Specifications of 1-215570-6

Rohs CompliantYESProduct TypeConnector
Type Of ConnectorPaddleboard ConnectorMount AngleVertical
Pcb Mount StyleThrough HoleInsulation Diameter (mm [in])0.90 [.035]
PolarizationWithNumber Of Positions16
Wire Range (mm [awg])0.08-0.09² [28]Centerline (mm [in])1.27 [0.050]
Contact Base MaterialPhosphor BronzeContact Plating, Mating Area, MaterialTin
Housing ColorRedHousing MaterialPolyester GF
Rohs/elv ComplianceRoHS compliant, ELV compliantLead Free Solder ProcessesWave solder capable to 240°C, Wave solder capable to 260°C, Wave solder capable to 265°C
Rohs/elv Compliance HistoryAlways was RoHS compliantApplies ToPrinted Circuit Board
Packaging MethodReelPackaging Quantity2,500
1
Page 1
2
Page 2
3
Page 3
4
Page 4
5
Page 5
6
Page 6
7
Page 7
8
Page 8
9
Page 9
10
Page 10
11
12
13
14
15
Page 1/15

Download datasheet (237Kb)Embed
Next
Product
Specification
AMP Micro-MaTch Miniature Connector Assembly
1.
SCOPE .
1.1
Content
This specification covers the general description and performance requirements of the AMP Micro-MaTch
Miniature Connector System, which includes a complete product-line of board to board and wire to board
interconnections
1.1.1
Qualification
When tests are performed on subject product, procedures specified in this Product Specification shall be
used. All inspections shall be performed using applicable inspection plan and product drawing.
2.
APPLICABLE DOCUMENTS.
The following documents form a part of this specification to the extend specified herein. Unless otherwise
specified, latest edition of the document applies. In the event of conflict between the requirements in this
specification and the product drawing, the product drawing shall take precedence. In the event of conflict
between requirements of this specification and referenced documents, this specification shall take
precedence.
2.1
AMP Documents
R041-1664
Test report Wire-To-Board connector
R041-1665
Test report Paddle-Board connector
R041-1666
Test report Female On Board SMC connector
R041-1846
Test report Female On Board SMD connector
R041-1847
Test report Female In Board SMD connector
501-19005
Test report Crimp-On Snap-In (COSI) connector
501-19094
Test report lead-free wave soldering-heat (IDC-connection Paddle-Board)
501-19093
Test report lead-free wave soldering-heat (Wave-solder connectors)
501-19092
Test report lead-free reflow soldering-heat (SMD connectors)
114-19016
Application Specification Micro-MaTch Miniature Connector System
114-19027
Application Specification Micro-MaTch Female SMC Connector
114-19051
Application Specification Micro-MaTch Crimp-on Snap-in Male on Wire connector
DR. H.v.Delft
Tyco Electronics Nederland B.V.
This information is confidential and propriety to Tyco
Electronics and its worldwide subsidiaries and affiliates.
All international rights reserved
It may not be disclosed to anyone, other than Tyco
Tyco Electronics
Electronics personnel, without written authorization from
Tyco Electronics Corporation, Harisburg, Pennsylvania USA
*Trademark
R6-76 (Rev. 07-01)
DATE 28/10 /98
APVD M.Gosselink
This specification is a controlled document and subject to
change. Contact the Engineering Control Organization for
the latest revision.
108 - 19052
19/Jun/06 Rev. F
DATE 30/10/98
EC EH10-xxxx-yy
1 of 15
LOC H

1-215570-6 Summary of contents

  • Page 1

    ... Tyco Electronics Electronics personnel, without written authorization from Tyco Electronics Corporation, Harisburg, Pennsylvania USA *Trademark R6-76 (Rev. 07-01) DATE 28/10 /98 APVD M.Gosselink This specification is a controlled document and subject to change. Contact the Engineering Control Organization for the latest revision. 108 - 19052 19/Jun/06 Rev ...

  • Page 2

    ... Products shall be of design, construction and physical dimensions as specified on the applicable product drawings. All connector types of the Micro-MaTch Miniature connector System are available from positions (only even numbers ) Centerline distance between contacts is 1,27 mm (0,50” multiple of this case of selectively loaded connectors, which are available for all versions. 3.2 Material and Finish: Contacts: Phosphor Bronze according DIN specifications, tinplated over nickel underlayer ...

  • Page 3

    ... Wire-to-board and/or Board-to-board connections with the connector system positioned on the solder side of the PC board -for instance Surface Mount Application- • Permanent connections of ribbon cable to PC board, using the Paddle board connector version. • Wire-to board connection with discrete wires. Rev. F R6-77 (Rev. 07-01) 108-19052 Page ...

  • Page 4

    ... COSI- cable specification The Micro-MaTch COSI connector is designed for untwisted discrete wires in the range from 20-28 AWG. - Maximum insulation diameter for wires between 20-24 AWG is ∅ 0. Maximum insulation diamter for wires between 24-28 AWG is ∅ 1.27 mm 3.6 Performance and Test description Ratings: − ...

  • Page 5

    ... SMD Female Top Entry with Male On Wire Paddle board Crimp on Snap In Rev. F R6-77 (Rev. 07-01 Ambient Temperature (°C) Female Top Entry with Male On Board B valid for: Female Top Entry with Male On Wire Female Side Entry with Male On Board SMD inboard with Male On Wire 108-19052 100 105 Page ...

  • Page 6

    ... Para 2.4.2. ( Reflow soldering method ) In acc. with: Tyco Test Spec 109-201 Reflow curve § 3.4.B.2. Procedures In acc. with IEC 512-2 test 3a. In acc. with IEC 512-2 test 4a. In acc. with IEC 512-2 test 2a. Under dry circuit conditions. All contacts measured. Page ...

  • Page 7

    ... Minimum time between 2 operations: 1 sec. 108-19052 In acc. With IEC 512-2 test 2a Under dry circuit conditions All contacts measured. In acc. With IEC 912 test 2a Under dry circuit conditions All contacts measured. In acc. With IEC 512-2 test 2a Under dry circuit conditions All contacts measured. ...

  • Page 8

    ... In acc. with IEC 512-7 test 13a (COSI 13b) In acc. with IEC 512-4 test 6d. In acc. with IEC 68-2-6 test Fc.procedure 8.2.1 At push in forces connecors must be supported by a part of the application tooling. ...

  • Page 9

    ... Paragraph 3.6.1 3.6.8 3.6.22 3.6.21 3.6.24 3.6.22 3.6.8 3.6.1 3.6.1 3.6.16 3.6.8 3.6.16 3.6.13 3.6.10 3.6.8 3.6.21 3.6.8 3.6.10 3.6.1 3.6.1 3.6.8 3.6.25 3.6.8 3.6.17 3.6.8 3.6.1 3.6.1 3.6.2 3.6.1 3.6.1 3.6.3 3.6.1 3.6.1 3.6.14 3.6.25 3.6.14 3.6.1 3.6.12 Page ...

  • Page 10

    ... Paragraph 3.6.1 3.6.9 3.6.22 3.6.21 3.6.24 3.6.22 3.6.9 3.6.1 3.6.1 3.6.9 3.6.13 3.6.9 3.6.13 3.6.9 3.6.1 3.6.1 3.6.9 3.6.25 3.6.9 3.6.1 Page ...

  • Page 11

    ... Termination strength in Newtons 108-19052 3.6.1 3.6.18 3.6.1 3.6.1 3.6.9 3.6.22 3.6.9 3.6.1 3.6.1 3.6.12 3.6.1 Paragraph 3.6.1 3.6.11 3.6.23 3.6.21 3.6.24 3.6.21 3.6.11 3.6.1 3.6.1 3.6.11 3.6.25 3.6.11 3.6.1 3.6.1 3.6.2 3.6.1 3.6.1 3.6.11 3.6.3 3.6.11 3.6.1 3.6.1 3.6.15 3.6.1 Page ...

  • Page 12

    ... Paragraph 3.6.1 3.6.10 3.6.6 3.6.7 3.6.23 3.6.21 3.6.24 3.6.21 3.6.10 3.6.6 3.6.7 3.6.25 3.6.10 3.6.6 3.6.7 3.6.1 3.6.1 3.6.11 3.6.25 3.6.10 3.6. 3.6.10 3.6.1 3.6.1 3.6.10 3.6.25 3.6.10 3.6.17 3.6.10 3.6.1 Page ...

  • Page 13

    ... Termination resistance 108-19052 Paragraph 3.6.1 3.6.12 3.6.1 3.6.1 3.6.4 3.6.1 3.6.1 3.6.5 3.6.1 Paragraph 3.6.1 3.6.8 3.6.23 3.6.21 3.6.24 3.6.21 3.6.8 3.6.1 3.6.1 3.6.16 3.6.8 3.6.13 3.6.16 3.6.8 3.6.21 3.6.16 3.6.8 3.6.1 3.6.1 3.6.8 3.6.25 3.6.8 3.6.17 3.6.8 3.6.1 3.6.1 3.6.12 Page ...

  • Page 14

    ... Damp heat cyclic, first cycle c) Cold d) Damp Heat cyclic, remaining 5 cycles 5. 6. Voltage proof 7. Visual examination 4. Rev. F R6-77 (Rev. 07-01) Measurements Insulation resistance Insulation resistance 108-19052 Paragraph 3.6.1 3.6.1 3.6.22 3.6.1 3.6.1 3.6.6 3.6.7 3.6.23 3.6.21 3.6.24 3.6.21 3.6.6 3.6.7 3.6.1 Page ...

  • Page 15

    ... At least 5 connectors of the 6 positions or at least 30 contacts shall be used for each testgroup. 4.1.2 Test sequence Qualification inspection shall be verified by testing samples as specified in spec. 108-19052 Par 3.7. 4.2 Requalification testing If changes significantly affecting form, fit or function are made to the product or the manufacturing process, product assurance shall co-ordinate requalification testing, consisting of all or part of the original testing sequence as determined by development/product, quality and reliability engineering ...