DS12C887 Maxim Integrated Products, DS12C887 Datasheet
DS12C887
Specifications of DS12C887
Available stocks
Related parts for DS12C887
DS12C887 Summary of contents
Page 1
... RAM (113 bytes in the DS12C887 and DS12C887A). The DS12887 integrates a quartz crystal and lithium energy source into a 24-pin encapsulated DIP package. The DS12C887 adds a century byte at address 32h ...
Page 2
Real-Time Clocks ABSOLUTE MAXIMUM RATINGS Voltage Range on V Pin Relative to Ground .....-0.3V to +6.0V CC Operating Temperature Range ................................................... Commercial (noncondensing) .............................0°C to +70°C Operating Temperature Range ................................................... Industrial (noncondensing)...............................-40°C to +85°C Storage Temperature Range EDIP ..................................................................-40°C to ...
Page 3
DC ELECTRICAL CHARACTERISTICS ( 3.0V over the operating range, unless otherwise noted.) (Note 2) CC BAT A PARAMETER SYMBOL V Current (OSC On); BAT T = +25° 3.0V A BACKUP V Current ...
Page 4
Real-Time Clocks AS t ASD AD0–AD7 WRITE AD0–AD7 READ AS t ASD DS t ASD R ASL AD0–AD7 WRITE 4 _____________________________________________________________________ Motorola Bus Read/Write Timing PW ASH t ASED t CYC ...
Page 5
AS t ASD DS t ASD R/W CS AD0–AD7 IRQ Release Delay Timing DS RESET IRQ t IRDS PF(MAX) V PF(MIN) RECOGNIZED INPUTS VALID OUTPUTS t CYC PW ASH t ASED ...
Page 6
Real-Time Clocks POWER-UP/POWER-DOWN CHARACTERISTICS (T = -40°C to +85°C) (Note 2) A PARAMETER SYMBOL Recovery at Power-Up V Fall Time PF(MAX) V PF(MIN) V Rise Time PF(MIN) V PF(MAX) DATA RETENTION (T = +25°C) ...
Page 7
T = +25°C, unless otherwise noted vs. V BAT1 BAT vs. TEMPERATURE +85°C CC 300 250 0°C +70°C +40°C 200 -40°C 150 2.5 2.8 3.0 3.5 3.3 V (V) BAT X1 ...
Page 8
Real-Time Clocks PIN SO, EDIP PLCC TQFP PDIP — — 5–10, 4–11 4– 15, 20 12, 17 ...
Page 9
... No Connection. This pin should remain unconnected. Pin 21 is RCLR for the N.C. DS12887A/DS12C887A. On the EDIP, these pins are missing by design. D ata Read Inp ut. The has ati end the l evel of the hen the connected sel ected . In thi osi the l atter the b us cycl e and i s cal ata str ob e ...
Page 10
... TQFP PDIP — (DS12887A DS12C887A ____________________________________________________________________ Pin Description (continued) NAME Active-Low Interrupt Request Output. The IRQ pin is an active-low output of the device that can be used as an interrupt input to a processor. The IRQ output remains low as long as the status bit causing the interrupt is present and the corresponding interrupt-enable bit is set ...
Page 11
... Detailed Description The DS12885 family of RTCs provide 14 bytes of real- time clock/calendar, alarm, and control/status registers and 114 bytes (113 bytes for DS12C887 and DS12C887A) of nonvolatile, battery-backed static RAM. A time-of-day alarm, three maskable interrupts with a common interrupt output, and a programmable square- wave output are available. The devices also operate in either 24-hour or 12-hour format with an AM/PM indica- tor ...
Page 12
... Refer to Application Note 58: Crystal Considerations with Dallas Real-Time Clocks for more detailed information. Clock Accuracy for DS12887, DS12887A, DS12C887, DS12C887A Only The encapsulated DIP modules are trimmed at the fac- tory to an accuracy of ±1 minute per month at +25°C. Power-Down/Power-Up ...
Page 13
... Read/Write Bit. * DS12C887, DS12C887A only. General-purpose RAM on DS12885, DS12887, and DS12887A. Note: Unless otherwise specified, the state of the registers is not defined when power is first applied. Except for the seconds regis- ter, 0 bits in the time and date registers can be written to 1, but may be modified when the clock updates. 0 bits should always be written to 0 except for alarm mask bits ...
Page 14
... Read/Write Bit. * DS12C887, DS12C887A only. General-purpose RAM on DS12885, DS12887, and DS12887A. Note: Unless otherwise specified, the state of the registers is not defined when power is first applied. Except for the seconds regis- ter, 0 bits in the time and date registers can be written to 1, but may be modified when the clock updates. 0 bits should always be written to 0 except for alarm mask bits ...
Page 15
Control Registers The real-time clocks have four control registers that are accessible at all times, even during the update cycle. MSB BIT 7 BIT 6 BIT 5 UIP DV2 Bit 7: Update-In-Progress (UIP). This bit is a status flag that ...
Page 16
Real-Time Clocks MSB BIT 7 BIT 6 BIT 5 SET PIE Bit 7: SET. When the SET bit is 0, the update transfer functions normally by advancing the counts once per second. When the SET bit is written to 1, ...
Page 17
MSB BIT 7 BIT 6 BIT 5 IRQF PF Bit 7: Interrupt Request Flag (IRQF). This bit is set to 1 when any of the following are true PIE = AIE = ...
Page 18
... Register C clears all active flag bits and the IRQF bit. Interrupts When the DS12887, DS12887A, DS12C887, and DS12C887A are shipped from the factory, the internal oscillator is turned off. This prevents the lithium energy cell from being used until the device is installed in a system ...
Page 19
Table 3. Periodic Interrupt Rate and Square-Wave Output Frequency SELECT BITS t PERIODIC PI REGISTER A INTERRUPT RATE RS3 RS2 RS1 RS0 None 3.90625ms 7.8125ms ...
Page 20
... AD1 5 DS12885 AD2 6 DS12885S AD3 7 AD4 8 AD5 9 AD6 10 AD7 11 GND 12 SO, PDIP NOTE: THE DS12887A AND DS12C887A CANNOT BE STORED OR SHIPPED IN CONDUCTIVE MATERIAL THAT WILL GIVE A CONTINUITY PATH BETWEEN THE RAM CLEAR PIN AND GROUND. 20 ____________________________________________________________________ SQW 22 N.C. 21 RCLR 20 V BAT 19 IRQ 18 ...
Page 21
... SUBSTRATE CONNECTED TO GROUND ____________________________________________________________________ Real-Time Clocks Ordering Information TOP MARK* DS12885 DS12885 DS12885Q DS12885Q DS12885Q DS12885Q DS12885S DS12885S DS12885S DS12885 DS12885 DS12887 DS12887A DS12C887 DS12C887AA Thermal Information THETA-JA (°C/W) THETA-JC (°C/ 105 Package Information PACKAGE CODE DOCUMENT NO. W24+1 21-0042 P24+4 21-0044 MDP24+1 21-0241 ...
Page 22
... Maxim cannot assume responsibility for use of any circuitry other than circuitry entirely embodied in a Maxim product. No circuit patent licenses are implied. Maxim reserves the right to change the circuitry and specifications without notice at any time. 22 ____________________Maxim Integrated Products, 120 San Gabriel Drive, Sunnyvale, CA 94086 408-737-7600 © 2010 Maxim Integrated Products is a registered trademark of Maxim Integrated Products, Inc ...