AD7730BRZ Analog Devices Inc, AD7730BRZ Datasheet - Page 17

• Manufacturer Part Number: AD7730BRZ
• Description: IC ADC BRIDGE TRANSDUCER 24-SOIC
• Manufacturer: Analog Devices Inc

Specifications of AD7730BRZ

• Data Interface: DSP, Serial, SPI™
• Number Of Bits: 24
• Sampling Rate (per Second): 1.2k
• Number Of Converters: 1
• Power Dissipation (max): 125mW
• Voltage Supply Source: Analog and Digital
• Operating Temperature: -40°C ~ 85°C
• Mounting Type: Surface Mount
• Package / Case: 24-SOIC (0.300", 7.50mm Width)
• Resolution (bits): 24bit
• Sampling Rate: 1.2kSPS
• Input Channel Type: Differential, Single Ended
• Supply Voltage Range - Analog: 4.75V To 5.25V
• Package: 24SOIC W
• Resolution: 24 Bit
• Architecture: Delta-Sigma
• Number Of Adcs: 1
• Number Of Analog Inputs: 2
• Digital Interface Type: Serial (3-Wire, SPI)
• Input Type: Voltage
• Signal To Noise Ratio: 123 dB
• Polarity Of Input Voltage: Unipolar|Bipolar
• Number Of Elements: 1
• Sample Rate: 1.2KSPS
• Input Polarity: Unipolar/Bipolar
• Differential Input: Yes
• Power Supply Requirement: Analog and Digital
• Single Supply Voltage (typ): 5V
• Single Supply Voltage (min): 4.75V
• Single Supply Voltage (max): 5.25V
• Dual Supply Voltage (typ): Not RequiredV
• Dual Supply Voltage (min): Not RequiredV
• Dual Supply Voltage (max): Not RequiredV
• Power Dissipation: 125mW
• Integral Nonlinearity Error: 18ppm of FSR
• Operating Temp Range: -40C to 85C
• Operating Temperature Classification: Industrial
• Mounting: Surface Mount
• Pin Count: 24
• Package Type: SOIC W
• Input Signal Type: Differential
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• For Use With: EVAL-AD7730LEBZ - BOARD EVALUATION FOR AD7730EVAL-AD7730EBZ - BOARD EVAL FOR AD7730
• Lead Free Status / Rohs Status: Compliant

Bit
Location
MR12
MR11
MR10–MR9 D1–D0
MR8
MR7
MR6
MR5–MR4
MR3
REV. A
Bit
Mnemonic
B/U
DEN
WL
HIREF
ZERO
RN1–RN0
CLKDIS
Description
Bipolar/Unipolar Bit. A 0 in this bit selects bipolar operation and the output coding is 00 . . . 000 for
negative full-scale input, 10 . . . 000 for zero input, and 11 . . . 111 for positive full-scale input. A 1 in
this bit selects unipolar operation and the output coding is 00 . . . 000 for zero input and 11 . . . 111 for
positive full-scale input.
Digital Output Enable Bit. With this bit at 1, the AIN2(+)/D1 and AIN2(–)/D0 pins assume their
digital output functions and the output drivers connected to these pins are enabled. In this mode, the
user effectively has two port bits which can be programmed over the serial interface.
Digital Output Bits. These bits determine the digital outputs on the AIN2(+)/D1 and AIN2(–)/D0 pins,
respectively, when the DEN bit is a 1. For example, a 1 written to the D1 bit of the Mode Register
(with the DEN bit also a 1) will put a logic 1 on the AIN2(+)/D1 pin. This logic 1 will remain on this
pin until a 0 is written to the D1 bit (in which case the AIN2(+)/D1 pin goes to a logic 0) or the digital
output function is disabled by writing a 0 to the DEN bit.
Data Word Length Bit. This bit determines the word length of the Data Register. A 0 in this bit selects
16-bit word length when reading from the data register (i.e., RDY returns high after 16 serial clock
cycles in the read operation). A 1 in this bit selects 24-bit word length for the Data Register.
High Reference Bit. This bit should be set in accordance with the reference voltage which is being used
on the part. If the reference voltage is 5 V, the HIREF bit should be set to 1. If the reference voltage is
2.5 V, the HIREF bit should be set to a 0. With the HIREF bit set correctly for the appropriate applied
reference voltage, the input ranges are 0 mV to +10 mV, +20 mV, +40 mV and +80 mV for unipolar
operation and 10 mV, 20 mV, 40 mV and 80 mV for bipolar operation.
It is possible for a user with a 2.5 V reference to set the HIREF bit to a 1. In this case, the part is oper-
ating with a 2.5 V reference but assumes it has a 5 V reference. As a result, the input ranges on the part
become 0 to +5 mV, +10 mV, +20 mV and +40 mV for unipolar operation and 5 mV, 10 mV,
main unchanged so the resolution of the part (in counts) will halve.
A zero must be written to this bit to ensure correct operation of the AD7730.
Input Range Bits. These bits determine the analog input range for the selected analog input. The dif-
ferent input ranges are outlined in Table XII. The table is valid for a reference voltage of 5 V with the
HIREF bit at 1, or for a reference voltage of 2.5 V with the HIREF bit at a logic 0.
Note that the input range given in the above table is the range that appears at the input of the PGA
after the DAC offset value has been applied. If the DAC adjusts out no offset (DAC Register is 0010
0000), then this is also the input voltage range at the analog input pins. If, for example, the DAC sub-
tracts out 50 mV of offset and the part is being operated in bipolar mode with RN1 and RN0 at 0, 0,
the actual input voltage range at the analog input is +40 mV to +60 mV.
Master Clock Disable Bit. A 1 in the bit disables the master clock from appearing at the MCLK OUT
pin. When disabled, the MCLK OUT pin is forced low. It allows the user the flexibility of using the
MCLK OUT as a clock source for other devices in the system or of turning off the MCLK OUT as a
power saving feature. When using an external master clock at the MCLK IN pin, the AD7730 contin-
ues to have internal clocks and will convert normally with the CLKDIS bit active. When using a crystal
oscillator or ceramic resonator across the MCLK IN and MCLK OUT pins, the AD7730 clock is
stopped and no conversions take place when the CLKDIS bit is active.
RN1
0
0
1
1
20 mV and 40 mV for bipolar operation. However, the output noise from the part (in nV) will re-
RN0
0
1
0
1
B/U Bit = 0
–10 mV to +10 mV
–20 mV to +20 mV
–40 mV to +40 mV
–80 mV to +80 mV
Table XII. Input Range Selection
–17–
Input Range
B/U Bit = 1
0 mV to +10 mV
0 mV to +20 mV
0 mV to +40 mV
0 mV to +80 mV
AD7730/AD7730L
Power-On/Reset Default