6605412-3 TE Connectivity, 6605412-3 Datasheet - Page 3

• Manufacturer Part Number: 6605412-3
• Description: 1X1 MAG45 4N2, 417, NO PNL TAB
• Manufacturer: TE Connectivity

Specifications of 6605412-3

• Product Type: Connector
• Number Of Cores: 6
• Magnetics: Integrated Magnetics
• Jack Type: RJ45
• Signal Routing Type: NIC
• Profile: Standard
• Pcb Mounting Orientation: Side Entry (Right Angle)
• Jack Configuration: 1 x 1
• Turns Ratio: 1:1
• Shielded: Yes
• Emi Finger - Bottom: Without
• Termination Method: Solder
• Port Configuration: Single
• Emi Fingers -top And Sides: Without
• Latch Orientation: Standard - Latch Down
• Pcb Tail Length (mm [in]): 2.54 [0.100]
• Contact Termination Type: Through Hole
• Preloaded: Yes
• Connector Style: Jack
• Status Indicator: None
• Decoupling Capacitor: 2KV
• Rear Pcb Ground Tab: Without
• Signal Lead Quantity: 8
• Rohs/elv Compliance: RoHS compliant, ELV compliant
• Lead Free Solder Processes: Wave solder capable to 240°C, Wave solder capable to 260°C, Wave solder capable to 265°C
• Rohs/elv Compliance History: Always was RoHS compliant
• Operating Temperature (°c [°f]): 0 – 70 [32 – 158]
• Applies To: Printed Circuit Board
• Environmental Conditions: Office / Premises
• Application: 10/100BASE-T Ethernet

Durability, 500 cycles.
Durability, 2000 cycles.
Mating force.
Unmating force.
Normal force.
Modular plug retention to modular
jack.
Thermal shock.
Humidity-temperature cycling.
Mixed flowing gas.
Extended temperature.
Rev D
Test Description
See Note.
See Note.
20.02 N [4.5 lbf] maximum.
See Note.
20.02 N [4.5 lbf] maximum.
See Note.
100 gram force [3.53 ozf] minimum
per FCC Part 68, Subpart F
Connector Requirements.
57.83 N [13 lbf] minimum.
Plug shall not disengage from jack.
See Note.
See Note.
See Note.
No discontinuities of 1
microsecond or longer duration at
temperature levels.
See Note.
Figure 1 (continued)
ENVIRONMENTAL
Requirement
EIA-364-9C.
Manually mate and unmate
specimens with the plug locking
tab inoperable for 500 cycles at a
maximum rate of 300 cycles per
hour.
EIA-364-9C.
Manually mate and unmate
specimens with the plug locking
tab inoperable for 2000 cycles at a
maximum rate of 300 cycles per
hour.
EIA-364-13B.
Measure force necessary to mate
specimens at a maximum rate of
12.7 mm [.5 in] per minute.
EIA-364-13B.
Measure force necessary to
unmate specimens at a maximum
rate of 12.7 mm [.5 in] per minute.
EIA-364-4.
Measure and record normal force
generated at any given deflection
level within the normal operating
range with an FCC compliant
modular plug.
EIA-364-98.
Subject mounted specimens to
specified force applied for 1 minute
in 4 directions with plug mated in
jack and latch engaged.
EIA-364-32C.
Subject mated and mounted
specimens to 5 cycles between -25
+0/-3 and 70 +3/-0° C with 60
minute dwell at temperature
extremes.
EIA-364-31B,
Method IV.
Subject mated and mounted
specimens to 10 cycles (10 days)
between 25 and 65° C at 90 to 95%
RH.
EIA-364-65,
Class IIA (4 gas).
Subject mated and unmated
specimens to environmental Class
IIA for 10 days.
Subject mated and mounted
specimens to 2 hours at each of
the following temperatures: -5, 25,
55 and 75 ± 2° C.
Procedure
108-2100
3 of 6