6610023-1 TE Connectivity, 6610023-1 Datasheet

6610023-1

Manufacturer Part Number

6610023-1

Description

1X4 MAG45(TM) 7N2ET,26ET,G/Y RLE

Manufacturer

TE Connectivity

Datasheets

1.1368398-1.pdf (6 pages)

2.6-6610023-1.pdf (2 pages)

Specifications of 6610023-1

Product Type

Connector

Number Of Cores

Magnetics

Integrated Magnetics

Jack Type

RJ45

Signal Routing Type

Auto MDI/MDIX

Profile

Standard

Pcb Mounting Orientation

Side Entry (Right Angle)

Jack Configuration

1 x 4

Turns Ratio

1:1

Shielded

Yes

Emi Finger - Bottom

With

Termination Method

Solder

Port Configuration

Multiple

Emi Fingers -top And Sides

Without

Latch Orientation

Inverted - Latch Up

Pcb Tail Length (mm [in])

3.68 [0.145]

Contact Termination Type

Through Hole

Preloaded

Yes

Connector Style

Jack

Status Indicator

LED

Decoupling Capacitor

Without

Rear Pcb Ground Tab

Without

Signal Lead Quantity

Rohs/elv Compliance

RoHS compliant, ELV compliant

Lead Free Solder Processes

Wave solder capable to 240°C, Wave solder capable to 260°C, Wave solder capable to 265°C

Rohs/elv Compliance History

Always was RoHS compliant

Left Led Color (position #1)

Green - 250 ohm resistor

Right Led Color (position #2)

Yellow - 250 ohm resistor

Operating Temperature (°c [°f])

-40 – +85 [-40 – +185]

Applies To

Printed Circuit Board

Environmental Conditions

Industrial / Commercial

Application

10/100BASE-T Ethernet

Current page: 1 of 6
Download datasheet (85Kb)

1.1.

1.2.

1.3.

2.1.

2.2.

3.1.

3.2.

drawing.

3.3.

a TE Connectivity Ltd. Company

TE logo is a trademark.

SCOPE

Content

This specification covers performance, tests and quality requirements for the TE Connectivity (TE)

Mag45* Modular Jacks with Integrated Magnetics.

Qualification

When tests are performed on the subject product line, procedures specified in Figure 1 shall be used.

All inspections shall be performed using the applicable inspection plan and product drawing.

Qualification Test Results

Successful qualification testing on the subject product line was completed on 20Jun00. The

Qualification Test Report number for this testing is 501-524. This documentation is on file at and

available from Engineering Practices and Standards (EPS).

APPLICABLE DOCUMENTS

The following documents form a part of this specification to the extent specified herein. Unless

otherwise specified, the latest edition of the document applies. In the event of conflict between the

requirements of this specification and the product drawing, the product drawing shall take precedence.

In the event of conflict between the requirements of this specification and the referenced documents,

this specification shall take precedence.

TE Documents

●

Industry Standards

●

REQUIREMENTS

Design and Construction

Product shall be of the design, construction and physical dimensions specified on the applicable

product drawing.

Materials

Ratings

●

Materials used in the construction of this product shall be as specified on the applicable product

109-197:

501-524:

502-1129:

ANSI X3.263:

EIA-364:

FCC Part 68:

IEEE 802-3:

MIL-STD-202: Test Method Standard - Electronic and Electrical Component Parts

MIL-STD-810: Test Method Standard - Environmental Engineering Considerations and

Voltage: 150 volts AC

Current: Signal application only

Product

Specification

Mag45* Modular Jacks With Integrated Magnetics

| Indicates Change

*Trademark

TE Test Specifications vs EIA and IEC Test Methods

Qualification Test Report

Engineering Report

Information Technology - Fibre Distributed Data Interface (FDDI) - Token Ring

Twisted Pair Physical Layer Medium Dependent (TP-PMD)

Electrical Connector/Socket Test Procedures Including Environmental

Classifications

Connection of Terminal Equipment to the Telephone, Connector Specifications

Local Area Networks: Carrier Sense Multiple Access With Collision Detection

(CSMA/CD) Access Method and Physical Layer Specification

Laboratory Tests

Other products, logos, and company names might be trademarks of their respective owners.

For latest revision, visit out website at www.te.com/documents

For Regional Customer service, visit our website at www.te.com

108-2100

30 Jan 12 Rev D

1 of 6

LOC B

Related parts for 6610023-1

6610023-1 Summary of contents

Page 1

... Mag45* Modular Jacks With Integrated Magnetics 1. SCOPE 1.1. Content This specification covers performance, tests and quality requirements for the TE Connectivity (TE) Mag45* Modular Jacks with Integrated Magnetics. 1.2. Qualification When tests are performed on the subject product line, procedures specified in Figure 1 shall be used. ...

Page 2

Temperature: ● • Standard 70° • Extended temperature varieties: -40 to 85° C 3.4. Product Codes Product Codes for this product family are H363, H364, H365 and H366 3.5. Performance and Test Description Product is designed ...

Page 3

Test Description Durability, 500 cycles. Durability, 2000 cycles. Mating force. Unmating force. Normal force. Modular plug retention to modular jack. Thermal shock. Humidity-temperature cycling. Mixed flowing gas. Extended temperature. Rev D Requirement See Note. See Note. 20.02 N [4.5 lbf] ...

Page 4

Test Description Humidity, non-operational Salt spray. Shall meet visual requirements, show no physical damage, and meet requirements of additional NOTE tests as specified in the Product Qualification and Requalification Test Sequence shown in Figure 2. 3.7. Product Qualification and Requalification ...

Page 5

QUALITY ASSURANCE PROVISIONS 4.1. Qualification Testing A. Specimen Selection Specimens shall be prepared in accordance with applicable Instruction Sheets and shall be selected at random from current production. Test group 1 shall consist of 16 specimens. Test groups 2 ...

Page 6

Rev D 108-2100 ...

Related keywords

6610023-1 datasheet
6610023-1 data sheet
6610023-1 pdf datasheet
6610023-1 component
6610023-1 part
6610023-1 distributor
6610023-1 RoHS
6610023-1 datasheet download