776538-2 TE Connectivity, 776538-2 Datasheet - Page 3

• Manufacturer Part Number: 776538-2
• Description: AS 16, 8P CAP ASSY, RD, KEY 2
• Manufacturer: TE Connectivity

Specifications of 776538-2

• Product Line: AMPSEAL 16
• Product Type: Connector
• Connector Type: Housing
• Mount Angle: Straight
• Mount: Mounting Clip
• Housing Style: Clip Mount Rails
• Mating Retention Type: Latching
• Seal Type: Peripheral and Wire Seals
• Centerline (mm [in]): 4.50 [0.177]
• Number Of Rows: 2
• Row-to-row Spacing (mm [in]): 5.30 [0.209]
• Number Of Positions: 8
• Mating Retention: With
• Fluid Type: Water
• Contact Type: Pin
• Contact Layout: In-Line
• Connector Style: Receptacle
• Mating Alignment: With
• Housing Color: Gray
• Mating Alignment Type: Color Coded, Keyed, Terminal Position Assurance
• Housing Material: Thermoplastic - GF
• Environmental Protection: With
• Rohs/elv Compliance: RoHS compliant, ELV compliant
• Lead Free Solder Processes: Not relevant for lead free process
• Rohs/elv Compliance History: Always was RoHS compliant
• Fluid Resistance: Immersion

Rev B
Low signal term ination resistance.
Voltage drop.
Insulation resistance.
Random vibration.
Durability.
Term inal retention, axial.
Mating/unm ating force.
Polarizing m ism ating force.
Maintenance aging.
Tem perature life.
Test Description
Contacts shall not dislodge m ore
6 m illiohm s m axim um for 14 and 16
AW G wire.
9 m illiohm s m axim um for 18 AW G
wire.
20 m egohm s m inim um .
No discontinuities.
See Note.
See Note.
than 0.8 m m .
135 N m axim um .
220 N m inim um .
See Note.
See Note.
(AW G) (am peres) m axim um )
W ire
Size
14
16
18
Figure 2 (continued)
ENVIRONMENTAL
MECHANICAL
ELECTRICAL
Requirem ent
Current
Test
13
10
8
Voltage Drop
(m illivolts
100
100
100
SAE J2030 6.3.
SAE J2030 6.2.
Measure connection resistance
across m ated term inals and
subtract bulk resistance of Equal
W ire Lengths (EW L).
SAE J2030 6.4.
Averaged m easurem ents after 30
seconds, 15 m inutes and 30
m inutes of current being applied.
EW L subtracted.
Insulation resistance at 1000 volts
DC adjacent term inals m easured
after 60 seconds or until
stabilization occurs.
EIA-364-28.
Subject m ated specim ens to 21 G's
rm s between 25 to 2000 Hz.
Twenty hours in each of 3 m utually
perpendicular planes.
SAE J2030 6.11.
50 cycles.
IEC 512-8, Test 51a.
Apply axial load of 111 N to
contacts at a m axim um rate of 10 N
per second (or 50 m m per m inute)
and hold for 10 seconds.
SAE J2030 6.9. and 6.10.
Measure force necessary to m ate
and unm ate specim ens at a
m axim um rate of 50 m m per
m inute.
SAE J2030 6.21.
Attem pt to m ate specim en against
polarizing or keying feature.
SAE J2030 6.6.
Insert and rem ove term inal for 8
cycles on 20% of the term inals.
EIA-364-17.
Subject specim ens to 120 ± 3° C
for 500 hours.
Procedure
108-2184
3 of 6