MCP4532-502E/MS Microchip Technology, MCP4532-502E/MS Datasheet - Page 4

• Manufacturer Part Number: MCP4532-502E/MS
• Description: IC DGTL POT 5K 128TAPS 8-MSOP
• Manufacturer: Microchip Technology

Specifications of MCP4532-502E/MS

• Package / Case: 8-MSOP, Micro8™, 8-uMAX, 8-uSOP,
• Taps: 129
• Resistance (ohms): 5K
• Number Of Circuits: 1
• Temperature Coefficient: 150 ppm/°C Typical
• Memory Type: Volatile
• Interface: I²C, 2-Wire Serial
• Voltage - Supply: 1.8 V ~ 5.5 V
• Operating Temperature: -40°C ~ 125°C
• Mounting Type: Surface Mount
• Resistance In Ohms: 5K
• Number Of Pots: Single
• Taps Per Pot: 128
• Resistance: 5 KOhms
• Wiper Memory: Volatile
• Digital Interface: Serial (2-Wire, I2C)
• Operating Supply Voltage: 2.5 V or 3.3 V or 5 V
• Supply Current: 0.0025 mA (Typ)
• Maximum Operating Temperature: + 125 C
• Minimum Operating Temperature: - 40 C
• Mounting Style: SMD/SMT
• Supply Voltage (max): 5.5 V
• Supply Voltage (min): 1.8 V
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant, Lead free / RoHS Compliant

MCP453X/455X/463X/465X
AC/DC CHARACTERISTICS
DS22096A-page 4
DC Characteristics
Supply Voltage
HVC pin Voltage
Range
V
to ensure Wiper
Reset
V
ensure Power-on
Reset
Delay after device
exits the reset state
(V
Supply Current
(Note 10)
Note 1:
DD
DD
DD
Parameters
Start Voltage
Rise Rate to
> V
2:
3:
4:
5:
6:
7:
8:
9:
10: Supply current is independent of current through the resistor network
11: When HVC/A0 = V
BOR
Resistance is defined as the resistance between terminal A to terminal B.
INL and DNL are measured at V
MCP4XX1 only.
MCP4XX2 only, includes V
Resistor terminals A, W and B’s polarity with respect to each other is not restricted.
This specification by design.
Non-linearity is affected by wiper resistance (R
temperature.
The MCP4XX1 is externally connected to match the configurations of the MCP45X2 and MCP46X2, and
then tested.
POR/BOR is not rate dependent.
)
V
T
V
Sym
V
V
DDRR
BORD
I
BOR
DD
DD
HV
IHH
, the I
Standard Operating Conditions (unless otherwise specified)
Operating Temperature
All parameters apply across the specified operating ranges unless noted.
V
Typical specifications represent values for V
DD
WZSE
DD
V
Min
V
2.7
1.8
—
—
—
—
—
SS
SS
= +2.7V to 5.5V, 5 kΩ, 10 kΩ, 50 kΩ, 100 kΩ devices.
current is less due to current into the HVC/A0 pin. See I
W
and V
with V
(Note 9)
WFSE
Typ
2.5
10
—
—
—
—
—
—
—
A
= V
.
DD
W
12.5V
V
), which changes significantly overvoltage and
8.0V
Max
1.65
600
250
5.5
2.7
and V
DD
20
5
+
–40°C ≤ T
B
= V
Units
V/ms
µA
µA
µA
µs
V
V
V
V
V
SS
.
A
Serial Interface only.
RAM retention voltage (V
Serial Interface Active,
HVC/A0 = V
Write all 0’s to Volatile Wiper 0
V
Serial Interface Active,
HVC/A0 = V
Write all 0’s to Volatile Wiper 0
V
Serial Interface Inactive,
(Stop condition, SCL = SDA = V
Wiper = 0
V
≤ +125°C (extended)
V
V
DD
DD
DD
4.5V
4.5V
DD
DD
DD
= 5.5V, F
= 5.5V, F
= 5.5V, HVC/A0 = V
<
≥
= 5.5V, T
The HVC pin will be at one
of three input levels
(V
© 2008 Microchip Technology Inc.
IL
IH
IH
, V
SCL
SCL
Conditions
(or V
(or V
A
IH
= +25°C.
= 3.4 MHz
= 100 kHz
or V
IL
IL
PU
) (Note 11)
) (Note 11)
IHH
specification
IH
RAM
). (Note 6)
) < V
IH
),
BOR