MCP4161-103E/P Microchip Technology, MCP4161-103E/P Datasheet - Page 34

• Manufacturer Part Number: MCP4161-103E/P
• Description: IC POT DGTL SNGL 10K SPI 8DIP
• Manufacturer: Microchip Technology

Specifications of MCP4161-103E/P

• Memory Type: Non-Volatile
• Taps: 257
• Resistance (ohms): 10K
• Number Of Circuits: 1
• Temperature Coefficient: 150 ppm/°C Typical
• Interface: SPI Serial
• Voltage - Supply: 2.7 V ~ 5.5 V
• Operating Temperature: -40°C ~ 125°C
• Mounting Type: Through Hole
• Package / Case: 8-DIP (0.300", 7.62mm)
• Resistance In Ohms: 10K
• End To End Resistance: 10kohm
• Resistance Tolerance: ± 20%
• No. Of Steps: 257
• Supply Voltage Range: 2.7V To 5.5V
• Control Interface: SPI
• No. Of Pots: Single
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant

MCP414X/416X/424X/426X
REGISTER 4-2:
DS22059B-page 34
bit 8
Legend:
R = Readable bit
-n = Value at POR
bit 8
bit 7
bit 6
bit 5
bit 4
bit 3
bit 2
bit 1
bit 0
Note 1:
R-1
D8
2:
The hardware SHDN pin (when active) overrides the state of these bits. When the SHDN pin returns to the
inactive state, the TCON register will control the state of the terminals. The SHDN pin does not modify the
state of the TCON bits.
These bits do not affect the wiper register values.
D8: Reserved. Forced to “1”
R1HW: Resistor 1 Hardware Configuration Control bit
This bit forces Resistor 1 into the “shutdown” configuration of the Hardware pin
1 = Resistor 1 is NOT forced to the hardware pin “shutdown” configuration
0 = Resistor 1 is forced to the hardware pin “shutdown” configuration
R1A: Resistor 1 Terminal A (P1A pin) Connect Control bit
This bit connects/disconnects the Resistor 1 Terminal A to the Resistor 1 Network
1 = P1A pin is connected to the Resistor 1 Network
0 = P1A pin is disconnected from the Resistor 1 Network
R1W: Resistor 1 Wiper (P1W pin) Connect Control bit
This bit connects/disconnects the Resistor 1 Wiper to the Resistor 1 Network
1 = P1W pin is connected to the Resistor 1 Network
0 = P1W pin is disconnected from the Resistor 1 Network
R1B: Resistor 1 Terminal B (P1B pin) Connect Control bit
This bit connects/disconnects the Resistor 1 Terminal B to the Resistor 1 Network
1 = P1B pin is connected to the Resistor 1 Network
0 = P1B pin is disconnected from the Resistor 1 Network
R0HW: Resistor 0 Hardware Configuration Control bit
This bit forces Resistor 0 into the “shutdown” configuration of the Hardware pin
1 = Resistor 0 is NOT forced to the hardware pin “shutdown” configuration
0 = Resistor 0 is forced to the hardware pin “shutdown” configuration
R0A: Resistor 0 Terminal A (P0A pin) Connect Control bit
This bit connects/disconnects the Resistor 0 Terminal A to the Resistor 0 Network
1 = P0A pin is connected to the Resistor 0 Network
0 = P0A pin is disconnected from the Resistor 0 Network
R0W: Resistor 0 Wiper (P0W pin) Connect Control bit
This bit connects/disconnects the Resistor 0 Wiper to the Resistor 0 Network
1 = P0W pin is connected to the Resistor 0 Network
0 = P0W pin is disconnected from the Resistor 0 Network
R0B: Resistor 0 Terminal B (P0B pin) Connect Control bit
This bit connects/disconnects the Resistor 0 Terminal B to the Resistor 0 Network
1 = P0B pin is connected to the Resistor 0 Network
0 = P0B pin is disconnected from the Resistor 0 Network
R1HW
R/W-1
TCON BITS
W = Writable bit
‘1’ = Bit is set
R/W-1
R1A
(1, 2)
R/W-1
R1W
U = Unimplemented bit, read as ‘0’
‘0’ = Bit is cleared
R/W-1
R1B
R0HW
R/W-1
x = Bit is unknown
R/W-1
R0A
© 2008 Microchip Technology Inc.
R/W-1
R0W
R/W-1
R0B
bit 0