MCP4011-202E/SN Microchip Technology, MCP4011-202E/SN Datasheet - Page 2

• Manufacturer Part Number: MCP4011-202E/SN
• Description: IC DGTL POT 2.1K 1CH 8SOIC
• Manufacturer: Microchip Technology

Specifications of MCP4011-202E/SN

• Taps: 64
• Resistance (ohms): 2.1K
• Number Of Circuits: 1
• Temperature Coefficient: 150 ppm/°C Typical
• Memory Type: Volatile
• Interface: Up/Down
• Voltage - Supply: 1.8 V ~ 5.5 V
• Operating Temperature: -40°C ~ 125°C
• Mounting Type: Surface Mount
• Package / Case: 8-SOIC (3.9mm Width)
• Resistance In Ohms: 2.10K
• End To End Resistance: 2.1kohm
• No. Of Steps: 64
• Resistance Tolerance: ± 20%
• Supply Voltage Range: 1.8V To 5.5V
• Control Interface: Increment Decrement
• No. Of Pots: Single
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant

MCP4011/2/3/4
1.0
Absolute Maximum Ratings †
V
CS and U/D inputs w.r.t V
A,B and W terminals w.r.t V
Current at Input Pins ..................................................±10 mA
Current at Supply Pins ...............................................±10 mA
Current at Potentiometer Pins ...................................±2.5 mA
Storage temperature .....................................-65°C to +150°C
Ambient temp. with power applied ................-55°C to +125°C
ESD protection on all pins ........... ≥ 4 kV (HBM), ≥ 400V (MM)
Maximum Junction Temperature (T
AC/DC CHARACTERISTICS
DS21978C-page 2
Electrical Specifications: Unless otherwise indicated, all parameters apply across the specified operating ranges.
T
V
Operating Voltage Range
CS Input Voltage
Supply Current
Resistance
(± 20%)
Note 1:
DD
A
SS
= -40°C to +125°C, 2.1 kΩ, 5 kΩ, 10 kΩ and 50 kΩ devices. Typical specifications represent values for V
.............................................................................................................
= 0V, T
2:
3:
4:
5:
6:
7:
8:
9:
ELECTRICAL
CHARACTERISTICS
A
Resistance is defined as the resistance between terminal A to terminal B.
INL and DNL are measured at V
MCP4011/13 only, test conditions are: I
MCP4012/14 only, test conditions are:
Resistor terminals A, W and B’s polarity with respect to each other is not restricted.
This specification by design.
Non-linearity is affected by wiper resistance (R
Section 6.0 “Resistor” for additional information.
For voltages below 2.7V, refer to Section 2.0 “Typical Performance Curves”.
The MCP4011 is externally connected to match the configurations of the MCP4012 and MCP4014 and then tested.
= +25°C.
Parameters
Resistance
Device
2.1 kΩ
10 kΩ
50 kΩ
5 kΩ
SS....................................
SS.....................
2.25 mA
1.4 mA
450 µA
90 µA
5.5V
Current at Voltage
J
) . .........................+150°C
-0.3V to V
Sym
V
V
V
R
I
DD
W
DD
DD
CS
AB
1.1 mA
450 µA
210 µA
40 µA
-0.3V to 12.5V
2.7V
with V
DD
W
A
1.68
40.0
Min
V
+ 0.3V
2.7
4.0
8.0
= 1.9 mA, code = 00h.
—
—
—
—
= V
SS
6.5V
DD
MCP4012 includes V
MCP4014 includes V
W
), which changes significantly over voltage and temperature. See
and V
Typ
1.8
0.3
2.1
45
15
10
50
—
—
5
B
= V
Comments
† Notice: Stresses above those listed under “Maximum
Ratings” may cause permanent damage to the device. This is
a stress rating only and functional operation of the device at
those or any other conditions above those indicated in the
operational listings of this specification is not implied.
Exposure to maximum rating conditions for extended periods
may affect device reliability.
SS
. (-202 devices V
12.5
2.52
12.0
60.0
Max
5.5
6.0
—
—
—
1
WZSE
WFSE
Units
µA
µA
µA
kΩ
kΩ
kΩ
kΩ
V
V
V
A
= 4V).
V
V
U/D:V
The CS pin will be at one of three
input levels (V
(Note 6)
5.5V, CS = V
2.7V, CS = V
Serial Interface Inactive
(CS = V
-202 devices (Note 1)
-502 devices (Note 1)
-103 devices (Note 1)
-503 devices (Note 1)
© 2006 Microchip Technology Inc.
DD
IH
= 1.8V, V
= 1.8V, CS:V
IH
IH
= 1.8V, V
, U/D = V
DD
Conditions
SS
SS
IL
= 2.7V to 5.5V,
IL
= 0V,
, f
, f
, V
U/D
U/D
IHH
IL
IH
IH
= 0V
or V
= 1 MHz
= 1 MHz
)
= 8.5V,
IHH
).